Models
>
MDG5500AWQ
MDG5500AWQ Maytag Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for MDG5500AWQ
Viewing 10 of 10
Manuals & Guides for MDG5500AWQ
Click to downloadKeep searches simple, eg. "belt" or "pump".
$22.91
This OEM drum support roller kit contains the parts needed to replace one roller on your dryer. This kit includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommen...
In Stock
Order now and your part arrives by Apr 6
$28.91
This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both h...
In Stock
Order now and your part arrives by Apr 6
$13.07
This part is located on the front bulkhead of the dryer and helps the drum to rotate smoothly and quietly. If you notice a screeching or metal-on-metal noise while your appliance is operating, you may...
In Stock
Order now and your part arrives by Apr 6
The roller shaft is also known as a support roller shaft or a drum roller axle. It is a part in your dryer that the drum rollers spin on, helping your dryer to tumble. If your appliance is noisy while...
No Longer Available
If your dryer is noisy while operating, or will not tumble at all, there may be an issue with the drum belt. Over time, the rubber can become brittle and snap, and the belt will need to be replaced. T...
In Stock
Order now and your part arrives by Apr 6
$46.07
This is a genuine OEM replacement lint filter for your dryer. It measures approximately 12.5 inches in length and is made of a nylon mesh material. It is important that your dryer has a lint filter in...
In Stock
Order now and your part arrives by Apr 6
$6.51
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is nois...
In Stock
Order now and your part arrives by Apr 6
If your dryer is making excessive noise, or it will not tumble, there may be an issue with the idler pulley wheel. The idler pulley wheel is attached to the idler bracket and is used to secure the dry...
In Stock
Order now and your part arrives by Apr 6
$36.42
This genuine OEM part is a radiant flame sensor for your gas dryer. It is used to determine when the temperature of the igniter is hot enough to ignite the gas. Once the igniter is hot enough, it allo...
In Stock
Order now and your part arrives by Apr 6
$13.07
This roller shaft washer is just under an inch in diameter and is used for some of Whirlpool's brands of clothes dryers.Sold individually.
In Stock
Order now and your part arrives by Apr 6
$28.91
This flat style igniter comes with a wire harness connector. This part ignites the gas within the dryer. Bracket is NOT included.
In Stock
Order now and your part arrives by Apr 6
$13.07
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.
In Stock
Order now and your part arrives by Apr 6
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mary
March 26, 2024
On motor there is a blue plastic washer thats chewed up whats it called n where do I get one
For model number MDG5500AWQ
Hello Mary, thank you for your inquiry. The plastic blue part is not sold individually. It is part of the motor. The Motor for series 55 is PS11741125 and the motor for series 10 PS3500892. Both of these have photos and videos. We hope this helps.
Was this helpful?
Thank you for voting!
Common Problems and Symptoms for MDG5500AWQ
Viewing 11 of 11Noisy
Fixed by these parts
How to fix it
Not Heating
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Too hot
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Door Pops Open
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Running With Door Open
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anthony from DeKalb, IL
- Parts Used:
- WP33001808
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint into venting area.
Removal of old lint collector and replace with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from park city, MT
- Parts Used:
- WP6-3129480, WP33001443, WP312535, 12001541, WP9703438
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
dryer squeeking
removed front panel,lifted top, removed drum and drive belt,remove old rollers and acc and instlled new and reinstalled dryer parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Haverhill, NH
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Dryer ran but would not heat
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are
... Read more
located on top of the gas valve. I borrowed my neighbor"s ohm meter and touched the two probes on the coils terminals to check for continuity and found that one of the coils read zero. I then took both of the coils out by removing two screws and tested each coil again. One coil read 500-850 and the other read zero. This meant that it was no good so I called for the part and received it in three days. I reassembled the parts and turned the dryer on and it fired up after a few seconds. It works as good as new. The part plus shipping was less than $30. My repairman would have charged me $150-$200. While the dryer was apart I gave it a good cleaning with a vacuum and a toothbrush in delicate areas. I also removed and cleaned the lint trap housing by removing two nuts. I didn't know much about gas dryers, but thanks to PartSelect I easily fixed it myself.
Read less
Was this instruction helpful to you?
Thank you for voting!