MED5707TQ1 Maytag Dryer - Instructions

Boyfriend stated it was simple, he removed the back and replaced the part using a few everyday tools.

just slide the new filter in.

repair was fairly cut and dry...if you have any handyman experience....the hard part was partselect web page...starts out easy to locate part if you have the correct model number....however after that it can be confusing as to what you are looking for part wise and if you have located the correct part....diagrams are helpful if you could see them and/or understand them or what you are looking for....as a novice can be fustrateing....even after calling partselect for help/explaination....other wise it went well for a repair and hopeful will get another 10yrs out of this dryer.....

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

1/4 inch nut driver to remove panel back cover(6), timer unit(2), and cut-off(1).
Pliers to aid in removing single wires from components.
Most wires on timer were in position specific connectors.

this was very was very easy. But I deviated from the You Tube instructions. One to release the motor pulley. I needed to use 2 adjustable wrenches for a longer lever. I needed to use a hammer to help release pulley. Second to remove the dryer cable I needed to use a small screw driver to aid in the release. ---- the part from the company was a perfect fit.

Unplug Dryer.
Disconnect dryer vent line from rear of machine.
Removed 8 screws holding back cover on.
Removed back cover.
Disconnect 2 quick connect wires from dryer heating element tube on right side of the machine.
Remove 2 screws holding element cover in place.
Remove cover and element.
Remove thermostat from unit and connect to new unit.
Re install parts in reverse order of above.

First, removed the bottom cover below the dryer door. This is just held on with two clips that can be pushed in with a flat screw driver. Then remove the springs that go from the bottom of the dryer to the inside of the dryer door. We had to remove the entire front of the dryer, so the easiest way we found was to loosen the two screws on the bottom of the front panel, but not remove them. Then pop up the top of the dryer. To lift the top, first remove the two screws under the little door where the lint trap goes. The top is hinged in the back, and it snaps down onto two clips that can easily be popped up with a flat screw driver) With the top opened, there are two screws accessible. When the front of the dryer is removed, there will be nothing to support the drum, so what we found was that if you rotate the drum, you'll find a point where there's a hole in the top of the drum. If you take the springs that you removed from the bottom of the door you can hook them into this hole, and hook the other end into a hole in the back wall of the dryer just behind the drum. The springs are the perfect size for this, and it keeps the drum from falling when you remove the front panel. then just disconnect the three wires going to the switch inside the front panel, and remove the two screws from the top of the front panel. It should then lift right off. The bearing can just be pulled away and the new one installed. Put everything together again in reverse order.

Followed simple instructions to replace two pulleys and belt. The Virtual Repairman helped me identify the cause in minutes. Took another 5 minutes to place the order and the part arrived two days later. Saved $125 at least. Thank you!

john

The cycling thermostat was found to be not working when I checked it with a ohm meter. I ordered the part waited and installed it and it work just fine.

1 screw to replace.

Removed 2 screws in the lint filter and popped off the top. Removed the 2 screws holding the front panel on. Slid the drum off and set aside. Replaced support rollers. Placed the belt over the drum and placed the drum back in the dryer. Wound the belt over the tensioner and motor pulley. Turned the drum to keep seal from folding up. Replaced front and top.

Tip: Use bungee cord or rope to hold top up and out of the way while doing this job.

Removed top panel in back of dryer. removed two hex head screws holding timer in place. Removed seven wires all color coded from timer, wires all are clip on for easy removal. Clipped wires to new timer and installed timer back in with the two hex head screws then replaced upper back panel. Plugged dryer back into electric socket. Job done.

Super easy to repair...I had to idea how to get started; but after watching the video from your site it was a breeze. Thanks for having "how to repair" videos on your site.

Repair kit came in 2 days..fantastic..thank you so much....with new rollers, belt and tension roller she works like new

We pulled the back off the dryer and we weren't sure where the problem was exactly. So we pulled off the heating element and the thermostat. The heating element seemed to be burnt out, so we ordered that and the thermostat. We got the parts very quickly, so we put them in and found that the dryer still didn't heat. There was another thermostat (trip thermostat) that we decided to order and try...bingo...that was it. Now it works like a charm.