YMEDZ600TB2 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JAMES from NORTH OLMSTED, OH
- Parts Used:
- WPW10359272, WPW10314173, W10837240
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set, Wrench set
Dryer made squeaking noise, then more of a rumbling noise.
Checked this site for most likely needed parts and ordered. Located full repair manual inside unit after removing lid. Followed instructions in manual to take apart and remove the drum; took pictures at each removal step and used pill organizer to keep screws in correct order and quantity. The metal cylinder in the center of the idler pulley had ground away so the idler pulley with bracket was replaced. (There was a lot of metal dust that had to be cleaned.) One of the rollers did not turn smoothly so that was also replaced. After putting drum back in, reversed the steps to reassemble and referred to photos to make sure did in correct order and did not forget anything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BOILING SPGS, PA
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
My dryer was squeaking with an occasional thump
Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from STONE CREEK, OH
- Parts Used:
- WPW10314173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dryer drum turned hard because rollers were worn
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from HUNTSVILLE, AL
- Parts Used:
- 4392067
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Sqeeking noise fron old worn belt and rollers
Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from VALDOSTA, GA
- Parts Used:
- 279640
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer was squealing
Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from Garland, TX
- Parts Used:
- 280114
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Broken Drum Belt
Just like the video, just followed the video
Thanks,
Thanks,
Was this instruction helpful to you?
Thank you for voting!
Annoying loud metal to metal screeching noise.
Took the front part of the dryer out, released tension on the idler pulley, took the drum out, and remove the old drum seal. Make sure you remove the old adhesive with sandpaper or wire brush. Put the new adhesive on the seal, not on the drum. Adhesive is very runny. Seal may need to be stretched to fit the drum. Set the seal on the drum, let sit a few minutes. Put everything back together.
Was this instruction helpful to you?
Thank you for voting!
dryer was not heating up
take off front bottom panel. use ohm tester on the heater coil element, (It had broken in back) remove screw holding it in place and the two red wires leading to the element. Pull out and replace. reinstall in reverse. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from SAINT CLOUD, FL
- Parts Used:
- W10837240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My idler pully was squealing
I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from COCOA, FL
- Parts Used:
- WPW10314173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Roller Berings were worn out - replaced both
Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from TULELAKE, CA
- Parts Used:
- WPW10314173
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
dryer making noise. order parts
YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russ from Vernal, UT
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A hole in filter
Remove old filter
Vacuum out
Install new filter
Vacuum out
Install new filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from GROVELAND, IL
- Parts Used:
- W10837240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Loud squealing when the dryer was running...especially on start up.
Simply followed the video that accompanied the part confirmation. Removed the top and front of the dryer. Removed the drum and belt. Unbolted (1 bolt) the Idler pulley and bracket and bolted on the new one. Reversed the sequence of disassembly and tried it out. The only minor difficulty was slipping the belt over the idler pulley after the drum was in place. This is where a second set of hands might be helpful to hold up the drum, while the other person puts the belt in place. Other than that, this was a simple repair and probably saved a couple hundred dollars for about 1.5 hours of my time. Thanks for the video...it was right on point, and made the job much easier.
Was this instruction helpful to you?
Thank you for voting!
cold air vent in dryer was broken
remove 3 screws vent comes out put new part in works grate just like new a gain
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from ELMA, WA
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Squeaky dryer
Ezee pezee lemon squeezee.
Was this instruction helpful to you?
Thank you for voting!