MDE17MNAZW1 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- gerald from LEBANON, PA
- Parts Used:
- 279640
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Loud squealing noise during operation
Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WIMAUMA, FL
- Parts Used:
- W11086603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken grill
With the instructional video the repair was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- curtis from STOCKBRIDGE, GA
- Parts Used:
- 279640
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
replace idler pully
first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from SAN DIEGO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch was broke
just followed the video directions, worked perfectly thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- j from TAZEWELL, TN
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
dryer would not run because catch did not hold tight enough to press door switch.
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Oakland, NJ
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
door latch broke
Pop out the old latch and replaced with a new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from glenford, OH
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch was cracked
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from NORTH EASTON, MA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not stay closed - so dryer kept shutting off
Followed Youtube video - quick & easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Goddard, KS
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door catch
the part fit perfectly, it just snaped right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Union Beach, NJ
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door whould not close enough for the dryer to work.
Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Canfield, OH
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
dryer door won't stay shut
I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melody from TEXARKANA, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer door wouldn't catch and stay shut
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from MAGNETIC SPGS, OH
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
pulley bad
pull the back off and replace the pulley.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from CLIFTON, NJ
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Pulley wheel broke apart
Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from KILLEEN, TX
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
door would stay closed
just replaced parys
Was this instruction helpful to you?
Thank you for voting!