MDG17PDAXW1 Maytag Dryer - Instructions

I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with the new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.

After replacing all the other fuses and sensors I finally replaced the Radiant Flame Sensor and it is working perfectly.

After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lot of time and money if I had read that earlier.

once the back is off remove belt from tentioner and remove v clip. smooth shaft with wd-40 and scotch brite , then install new idler replace v clip
and your done !!!

Just like video except there were two screws in back to take control head off. Be prepared to have shop vacation ready. Clean dryer duct too. Have bandaids ready. Plastic triangles are not easy to take off, video makes it look easy.

Took the old filter out and inserted the new one- works great!!

Pulled out the old and slid in the new filter

Remove compactor drawer
Remove screws holding compactor to counter
screw in adjustable feet a short distance
slide compactor out far enough to unplug
loosen top screws that hold tiedown strips and move tie down strips out of way
remove two phillips screws on control panel
push control panel assymbly up and out of front of compactor
remove and replace wires one at a time onto new switch
remove two phillips screws on old switch and removeswitch.install new switch with same screws
install front switch assy by inserting in front panel of compactor and pushing down untill two holes match up for phillip screws.
install screws
realign both tie down straps and tighten screws
plug in compactor
push compactor back into place
level compactor with adjustable feet
replace tiedown screws to underside of counter
replace compactor drawer
push on/off switch to on. push start switch to start compactor.
watch as compactor stops at end of cycle. Hurrah!!

Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.

I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you

Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.

Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!

I ordered the dryer repair kit and to my surprise it arrived 4 days early. I followed the video instructions on the parts select website to replace 4 rollers, belt and belt pulley. A 1/4 in nut driver attached to my Dewalt drill made life ALOT easier!! My recommendation, when you remove the rollers, take a rag and really clean up the shaft they ride on. Then apply a lightweight spray oil to the shafts. When you install the new rollers they will spin free and easy. Having the dryer apart is also a great time to break out the dust buster of vacuum. Spin the fan motor up front by hand and use vacuum to remove lint or belt shaving from inside the cabinet. Add this step as good fire prevention measure.

Opened the lid and removed screws hollding switch to cabinet. Had to use magnifying glass to find locking mechanism on the electrical harness. Used small bladed screwdiver from my computer maintenaqnce kit to disengae lock. Hooked up harness. Replaced screws and shut lid. Main difficulty is my near vision. Requires use of a magnifier I am 80 years old). Your video is great. Gives step by step instructions.

After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.

Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.