MDE17PRAZW1 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cindy from BENZONIA, MI
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screen ripped
Dropped new filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from CARY, NC
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from LOGANVILLE, GA
- Parts Used:
- WPW10237959
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Broken dryer door switch
Never did get the part. Initial order was not the right part. Ordered the right part on 12.2 and this is 12.18. While the initial oder and delivery was correct, they do not tell you that you do not have to ship by Fed ex. Fed Ex seems to not be able to provide service to our address despite driving past it several times a day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WIMAUMA, FL
- Parts Used:
- W11086603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken grill
With the instructional video the repair was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- curtis from STOCKBRIDGE, GA
- Parts Used:
- 279640
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
replace idler pully
first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONNA from SAN LORENZO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
catch was missing to close dryer door
The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from LEBANON, PA
- Parts Used:
- 279640
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Loud squealing noise during operation
Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from SAN DIEGO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch was broke
just followed the video directions, worked perfectly thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- j from TAZEWELL, TN
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
dryer would not run because catch did not hold tight enough to press door switch.
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from glenford, OH
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch was cracked
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from NORTH EASTON, MA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not stay closed - so dryer kept shutting off
Followed Youtube video - quick & easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Goddard, KS
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door catch
the part fit perfectly, it just snaped right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Canfield, OH
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
dryer door won't stay shut
I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Oakland, NJ
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
door latch broke
Pop out the old latch and replaced with a new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from ALBANY, OR
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lint screen tore and had a side that was loose so it didn't catch all the lint and cut your fingers
Removed the old screen and simply put in the new one
Was this instruction helpful to you?
Thank you for voting!