MLG24PDAWW1 Maytag Dryer - Instructions

I ordered the top 5 items that may cause this problem based on the troubleshooting guide presented by the technicians I found in youtube. I replaced the coils and that fixed the problem. The coils are the first to go out according to techs, but I have the other parts just in case I may need them later on. My Maytag dryer which is over 19 years old is alive and working again. The coils are accessible from the bottom access panel secured by 2 nut screws, unplug the dryer first, then the coils are secured by a bracket with 2 small philips head screw, I used a stubby philips screw driver to remove the bracket, undo the 2 electrical connectors on the coils one with 2 prongs and the other with 3 prongs. Put the new coils attached the electrical connectors and secured them with the bracket. Checked for any loose wiring ensuring connectors are secured in place, then test run the dryer with the panel off so you can see the if the flame stays on, if you run the dryer without wet clothes the flame may stop after 15 or so minutes. It is better to test run the dryer with wet clothes just like when your drying fresh washed and wringed clothes. It was really easy, good luck!

took 2 screws out and replace new coils

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.

Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed front panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.

Replaced 4 wheels and new belt

Remove old filter
Vacuum out
Install new filter

Ezee pezee lemon squeezee.

As many of the other posts here on this website mentioned, I had the same problem of the dryer not heating up. I removed the front panel (4 screws on each side inside of door - easy - followed instructions) and once off I was able to view the igniter glowing properly so I knew the starter/igniter was not the issue. Everything I read then suggested that it must be the two terminal gas valve coil, and sure enough it was. Ordered part -- got it in literally a couple days -- removed bracket (two screws) put in new coil -- turned it on -- works great. Could not have been easier. This is a great website and would recommend it to everyone who is a Do It Yourselfer.

Really an easy fix. 2 5/16" screws hold the cover on below the dryer door. From here it's easy access to the gas element. 2 more screws for the valve cover and disconnected the attached wires to the gas coil valves. slip the news ones in place, re-attach the wires and install the holder.Tested the dryer and it fired right up. Put panel back in place and the wife is happy it didn't cost us more than just the parts. Yep, she's a lucky girl. ;0)

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.