MDG22PNAGW0 Maytag Dryer - Instructions

The other comments from folks who had done this were very helpful!
I had to go look up the directions for removing the door. To do this flip the latches on the hinges and then close the door as far as you can and pull up, it will come out.
Now lay the door flat on the kitchen counter and take out the 6 screws you can see on the edges and inside of the door. They are all the same so you don't have to keep them organized. Now you can take off the outer door with the handle (lift the inner door out since you will have the door face down at this point) and get it out if the way. Remove the hinges and set them aside but don't get them mixed up.
Next, take out the screws on the inner glass rails, there are two rails. Keep those rails in order for replacement. Take out the middle glass and clean it (this took oven cleaner and a razor blade on the one I had).
Take the middle of the door apart and expose the soft gasket (don't move it!). Clean out any broken glass and Insert your new glass. Put the middle piece of the door back on and line up all the screw holes! Put the first of the glass rails back on and the cleaned middle glass back in place, then the second glass rail. Put in the two screws that hold the glass rails.
Now you are ready to put the door back together. USE THE BOX TO HOLD THE DOOR OFF THE COUNTER WHILE YOU PUT THE HINGES BACK IN AND PUT THE DOOR FRONT BACK ON! If the screw holes don't all line up start the screws and work your way around, you'll get them to go in.
Voila! Door fixed.

Just like the video, just followed the video
Thanks,

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.

Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.

I am not the handiest guy around so i was a little nervous doing this job but figured i would take a crack at it ( no pun intended). Took the door off as per instructions from kitchenaid , unscrewed all the outer screws , took off the back of door unscrewed the metal bar holding the glass in ( there are 3 levels of glass) took the 2 good glass sheets out got to the broken glass removed that put the new one in , replaced all the other glass and screws and put door back on, and i felt so proud. Probably saved about 150 dollars by doing it myself. I feel so proud.

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

It was a matter of swapping out the old door with new door. In all, it was a snap . Around 10 screws to take it apart and a few brackets to hold it all together.

After opening the bottom access panel, I found a lot of lint build up which is very flammable. I took my leaf blower and cleaned it all out. Then I just followed the instructions that came with the part. But be careful as the igniter is fragile. I broke the first one...

Took the old parts out and installed the new parts in , everything that you sent fit perfect!!!!!

Checked fuse with Volmeter, had continuity (acted as a short) not the problem. Disconnected Hot Surface Igniter 2 Position connector to check resistance for a range of 50-300 Ohms of resistance with Voltohm Meter. Meter read open (High Resistance). Removed Igniter by unscrewing 5/16" hex nut on igniter plate assembly and noticed silicon carbide element was cracked in the middle. Ordered a new igniter and noticed assembly was required. Be careful here as igniter element is fragile, also do not touch it with your bare hands. You have to lay down on floor to reinstall igniter assembly and you might want to practice anchoring the defective igniter to gain confidence. Finally with slow movements anchored new igniter assembly and turned on dryer. Watched igniter glow heating gas valve and heating gas flame returned. Dryer fixed for a few hours of study online and cost only $24, plus learned how the gas dryer works.

This was more difficult than anticipated - probably because I'd never done it before. Once I got the door off (I didn't have the proper pins and used nails but didn't realize they had to be headless) I found all the screws, which were relatively easy to take out. I was surprised that the thermal door glass was obscured by two other panes of glass. It took more disassembly than anticipated and a few false starts when reassembling, but all in all it got done. I was happy that a job that would have cost probably $300 or more ended up getting done for $40 plus my labor - which isn't worth much these days. I'd certaily do it again.

How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.

I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!