MDE22PRBYW0 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edwin from PASADENA, TX
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Idler pulley broke off.
Took back panel off, and it was really easy putting the new idler pulley in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DW from ALVIN, TX
- Parts Used:
- WP8577274
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
F-26 Fault message
Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger
Thank You.
DW Pranger
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- curtis from STOCKBRIDGE, GA
- Parts Used:
- 279640
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
replace idler pully
first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from MAGNETIC SPGS, OH
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
pulley bad
pull the back off and replace the pulley.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from CLIFTON, NJ
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Pulley wheel broke apart
Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from ALBANY, OR
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lint screen tore and had a side that was loose so it didn't catch all the lint and cut your fingers
Removed the old screen and simply put in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Pompton Plains, NJ
- Parts Used:
- WP99002069
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Stinky dishwasher
When I tried to remove the hold down screw for the impellar, the impellar broke in half. I actually did npt need to go this far with disassembly as the problem was with water being retained in the rinse arm assembly and stagnating. This was due to calcium buildup clogging the drain holes. Clearing the holes resolved the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from St. Louis, MO
- Parts Used:
- WPW10512946
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from Marietta, GA
- Parts Used:
- 279973
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Dryer stopped heating
Determined via multimeter that either the thermostat or thermal fuse were not working, so ordered the kit (best value, contains both parts).Easiest access is from the rear, so removed rear panel and top of dryer (required) and also the vent tube since it was in the way. Unhooked wires from both parts, used socket to remove nuts holding each one on, put new ones in place, re-attached wires. Replaced vent tube, vacuumed entire inside of dryer (good idea). Put back/top back on and the dryer worked/heated perfectly immediately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from Puyallup, WA
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Squeaky tension pulley
Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from New York, NY
- Parts Used:
- WP99002069
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
No water pressure from lower wash arm
Never having repaired a dishwasher before, I disassembled everything I dared to until I found the root of the problem--part of the impeller had broken into several little bits. It wasn't apparent where the pieces came from, but the on-line diagrams and product photos helped. The broken impeller didn't want to come off the shaft, so I just crunched it up with a pair of vise grips. That seemed to be the gentlest solution for the pump bearings. The bits of impeller also took out the pump housing, which I could have ordered with the impeller had I been more observant. [insert four more days of washing by hand here] Inspect all parts for damage and clean out all stray chunks of food and plastic before reassembling!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from GOODYEAR, AZ
- Parts Used:
- WPW10159996
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Wrong parts were shipped, phone calls got continuous recordings to send email. Sent email sent on 4/2/2020 and now 4/14/2020 no response and no return of $20.52.020
Had to call service company to come and do the repair and they had the correct parts. PARTSELECT is a very terrible company to do business with. They sent incorrect parts and will not answer the phone or respond to emails after two weeks. will report to BBB.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from ENDICOTT, NY
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from SAN DIEGO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch was broke
just followed the video directions, worked perfectly thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- j from TAZEWELL, TN
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
dryer would not run because catch did not hold tight enough to press door switch.
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this instruction helpful to you?
Thank you for voting!