MEDZ600TW1 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MICHAEL from Baden, PA
- Parts Used:
- W10837240
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Squealing when running
You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annde from JEFFERSON CTY, TN
- Parts Used:
- W10837240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dryer was very loud and sounded like it was scraping
Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from ELMA, WA
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Squeaky dryer
Ezee pezee lemon squeezee.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwayne from Bainbridge, PA
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Dryer would shut off mid way through cycle and give an E1 error code
After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from HUNTINGDON VY, PA
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad screaming noise
Replaced 4 wheels and new belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Annapolis, MD
- Parts Used:
- WP3387223
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Clothes were not drying on auto sensor.
Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Madeline from PANA, IL
- Parts Used:
- WP8577274
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
YouTube video dated 9/28/2015
How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from STATE COLLEGE, PA
- Parts Used:
- 279787
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
dryer did not run
remove top, front, drum, fan fan housing, replace motor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clinton from MINOOKA, IL
- Parts Used:
- WPW10314173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer would squeal when the drum was turning
I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyle from HANOVER, IL
- Parts Used:
- WP8577274, WP22002263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Dryer won’t start
Drum belt broke. Found drive shaft belt guide broke. Replaced pulley wheel since I had it apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Candido from GREENVILLE, TX
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dryer won't start.Only make a click noise.
Remove top,front and panels.change thermal fuse and outlet thermistor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from JUNCTION, TX
- Parts Used:
- WP22002263
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bulb worked for a couple days and has now burned out, filaments dangling
To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.
I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.
I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILFRED from NORTH HIGHLANDS, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I recieved the kit the next day after ordering. It took about two seconds to do the repair
all that was required was to push the catch into the slot notools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Washington, DC
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door latch catch broke
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from ORANGE, CA
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer was not running as fast as normal, belt was squeaking loudly
The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.
Was this instruction helpful to you?
Thank you for voting!