YMED6300TQ0 Maytag Dryer - Instructions

got my daughter's boyfriend over.. he is like McEiver.. can fix anything with a bobbypin.... he told me what to order, you delivered it in 2 days.. and the dryer was fixed the next day. All it cost me was a roast beef dinner
Much better than that repairman who would have charged a minimum of $100 plus parts... at probably triple your cost...

Thanks to the sep by step instructions I got from part select this repair was very simple. The disassembling was relatively easy, my new maintainance kit came the nest day, the machine was already apart and the parts went in without a hitch. THANKYOU

I watched the video on the websit and it told me and showed me just what to do. Exccelent video, Ordered the repair kit, got it in two days. Job took me about 10 min.

i removed the old lens,then removed the bulb,after ordering and receiving your replacement lense,it went back on just like the old one.the repair was very easy. thank you. D.S P.S1 IAM A REPIARMAN NOW!!! WITH YOUR VIRTUAL REPAIRMAN APP,VERY VERY SMART ILL SPREAD THE WORD.

Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. reinstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.

Installed new belt and cleaned dust and wiped out inside of drum with Fantastic and clean sponge.

shook bottle and painted waited a day and repeated

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I had to remove the back, top and the tumbler to get to the fan...there are instuctions near the motor that tell you how to remove the fan and in which direction to turn...really is easy, just keep track of how the tumbler belt is routed on the pulley of the motor before you take it off.

Took off the front of & lifted the top up. Pulled the drum out & replaced the two wheels that turn the drum, replaced the belt & replaced the pully wheel that turns the belt & dryer motor & put back together. The dryer now runs like a new one. Has no noise when running.

Very easy, viewed the you-tube video and followed the instructions. Simply, unplug dryer, remove back panel (4 nuts), open back, remove one screw that holds board in place and slide left to remove. Take a picture of wire configuration to ensure you reconnect the same way. For the most part it is self explanatory for the exception of the hot wire and two ground wires and proceed to disconnect wires, install new board by reconnecting wires and proceed to replace back cover. Reconnect power source and get to drying.

Found a DIY video clip on YouTube...Ordered the parts...I only needed a replacement belt but PartSelect had an upgrade kit that included not only the belt and rear drum support wheels, but also the tensioner arm with a WHEEL instead of just the flat metal belt guide ( which I believe lead to the belt wearing out in the first place) All the parts fit perfectly and now it's better than new.

Took the back dryer cover off and removed the lint cover all from the back of the dryer then replaces the Thermistor (held with 2 screws).

Belt was worn, rollers were sticking, idler worn out. Ordered a kit to care for these issues, as usual the reapirs took almost no time. Dryer became a bit quieter for a first load, second load the motor siezed. I priced rebuilding most of the machine and determined replacement was due.