MDE17PRAYW0 Maytag Dryer - Instructions

First I removed the top back plate and found the electrical schematic, found the fuse and themostat. Went to Whilpool web site found exploded parts list to identify part (fuse)

removed fuse and tested with MM for an open. It was. Shorted the leads to verify that the Dryer operated. Found your site and was easily able to identify the part from the excellent description and pictures. Ordered it, installed it work great thanks

Checked on your website for common problems w/this model dryer,highest probability was the thermal fuse being blown,so I ordered one & checked the vent for being plugged,no problem there,removed the back of the dryer replaced the fuse(very easy to do)put everything back together & started it up...all set now.Thanks for your help

I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.

Dropped new filter in.

Never did get the part. Initial order was not the right part. Ordered the right part on 12.2 and this is 12.18. While the initial oder and delivery was correct, they do not tell you that you do not have to ship by Fed ex. Fed Ex seems to not be able to provide service to our address despite driving past it several times a day.

I removed the back of the dryer, removed the single screw holding the fuse in place and checked it for continuity. It didn't work, so I placed an order and 3 days later I was back in business. the replacement took about five minutes.

this was a super easy job! i unplugged the dryer, removed the back panel, located the fuse on the bottom left side, replaced it, put the panel back on, plugged it back in and IT WORKED! this was the first appliance repair job for me and i am so glad i found this site. it probably saved me $100.00 or so doing it myself. thank you!!!

I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.

I watched the video several times before beginning, which was very helpful. As I didn't have the tool that was recommended in the video, I used pliers, which although took longer, worked out fine. I also used pliers to pull the wires off of the old thermal fuse. My dryer had been not working for 2 months, so I was very pleased that I was able to watch a very detailed video, order the parts on the same website, and receive them very quickly (within couple of days.) My daughter who lives in another state googled my dryer model number with a description of the problem and found your website. She sent me the link of the video to watch as it appeared very easy to understand. She and I both were very impressed by the step-by-step instructions on the video, including a list of all the tools required. I am an 81 year old woman and had no problems fixing this by myself with the assistance of your website. I have recommended this site to several of many friends and family members. Thank you!

I guess you could say I went through the process of elemanation, first I replased the thermostat,removed 2 screws pulled off 3 wired with a pair of pliers put them on the new one, still no hot air so I replaced the fuse, took out 1 screw removed 2 wires and placed them on the new fuse, still no hot air, finally I replaced the thermal cut-off switch and WOW that was it hot air was blowing again, the process was very easy I ordered everything from parts slect and they were here the next day, only had to take the back off the dryer with a nut wrench, locate the thernastat, fuse and thermal cut-off which was just above the heating coil I removed 1 screw pulled off 2 wires and place them on the new one. very easy and the repair storys really helped locating the problem

So I opened the back up, and looked down the flame shoot and I could see that the igniter was never glowing red. (You can actually see the red glow of the igniter when its working right, then you here the solonoid click and flame. But again all this when its working correctly.) So anyway, no heat no glowing red.

I took the voltmeter out, grounded 1 lead and just followed the voltage (using the schematic provided), through the switches, yada yada trying to trace how far it got.

Voltage got to 1 side of thermal fuse, but not to other side. Bingo. Disconnected fuse and did continuity check - open. All of this took diagnosing took 1/2 hour to hour. Not really counting toward fix. Ordered the part at parts select. Put a jumper over the fuse so that clothes could still be dried (probably not recommended but it works). Part arrived in 2 days. Didn't even put the back panel on.

The part is right on the back. 1 screw, 2 space terminals. Takes all of 3 minutes to replace. Then another 5 minutes to put the back panel on and vent hose back on. Most of that is because you are working in a cramped space. (I don't have the biggest laundry room.)

Can't beat parts select!

Parts select + a little know how, saved me about $400.

removed cover then pulled wires with a plier, unscrewed the fuse and installed new fuse then put back cover plugged in power cord, fired dyer and run dryer for 2 minutes and felt warm air coming out of the exhaust.

Took off the backplate of dryer, replaced fuse, done.

The major issue was getting the dryer out and cleaning it all up. That's what took the time but it was worth it to clean out the lint in the ducts, etc.. Putting the thermal fuse was a snap thanks to the great feedback received when I got this web site and read the previous responses.

Pop out the old latch and replaced with a new one