DG102 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JOHN from JUPITER, FL
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
THE LOWER RACK WAS CORRODING IN SPOTS AND WAS RUSTING
THERE WERE NO INSTRUCTIONS INCLUDED, COULDN'T FIGURE 0UT HOW TO INSTALL THE NEW ROLLERS ON THE NEW RACK FINALLY INSTALLED THE OLD ROLLERS ON THE NEW RACK AND THEY WERE MUCH EASIER TO INSTALL I DONT UNDERSTAND
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Rochester, IL
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Rack Was Rusting Out
Kit didn't have the center conical piece. Easy to switch tho. I am impressed at the speed of which the part arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from St Johnsbury, VT
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lower rack started to rust through coating
Since there were no printed instructions, we looked at the photo schematic.
Reassembly using the photo was easy by putting the old rack alongside the new one and adjusting the new rack spacing to match the old one.
We also had new wheels which snapped on.
We were delighted to repair and replace this good, older dishwasher rather than purchase a new one!
Reassembly using the photo was easy by putting the old rack alongside the new one and adjusting the new rack spacing to match the old one.
We also had new wheels which snapped on.
We were delighted to repair and replace this good, older dishwasher rather than purchase a new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Peoria, AZ
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
original dishrack had become rusty
installed a new rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from JACKSONVILLE, FL
- Parts Used:
- W11169039
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper dish rack broken tines
Swapped out the old upper dish rack with a new one. A video made the change simple.
Was this instruction helpful to you?
Thank you for voting!
Power cord was damaged
Unscrewed the power cord and replace the old power cord with the new one I purchased through Partselect.com
Thanks for everything Partselect!!!!
Thanks for everything Partselect!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- susan from Socorro, NM
- Parts Used:
- WPY015825
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Both motor clips broken - >40 year old dryer!!
Removed the back - Saw the broken clips on the base of the dryer (the wires to the motor were pulling out because the motor was slipping).
Guessed that the parts were motor clips (no pix in the web site!)
Got the parts in post - they were identical except needed some rubber grips inside to hold tight (Used pieces of bike tire inner tube cut to fit for this.) Attached clips. Works fine!!
(Son is an engineer - he found the problem. Husband is a retired doctor - he couldn't!! but together they
supplied the muscle)
Sue (67 years old)
Guessed that the parts were motor clips (no pix in the web site!)
Got the parts in post - they were identical except needed some rubber grips inside to hold tight (Used pieces of bike tire inner tube cut to fit for this.) Attached clips. Works fine!!
(Son is an engineer - he found the problem. Husband is a retired doctor - he couldn't!! but together they
supplied the muscle)
Sue (67 years old)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Dayton, TX
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Dishrack Tines were breaking off due to age
The rack came with pictorial instructions which were fairly veg, however they were to the point. The wheels snapped into place easily, and the center water transfer tube twisted off the old one and twisted on the new one just fine. It is a very good idea to keep the old one out to look at as a guide. There were no instructions on how to remove the transfer tube, I was lucky to have already worked on these before. After that it fits and works just peachy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Chadds Ford, PA
- Parts Used:
- WP312535
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
worn roller wheel and bearing
replaced worn parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Coos Bay, OR
- Parts Used:
- W10311986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
We needed a new bottom dishrack the old one was very rusty
I ordered a new rack, snapped the stuff together, and slid the old one out and the new one in. Fit beautifully. Piece of cake and much cheaper than a new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Greene, ME
- Parts Used:
- W10311986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Installed wheel assemblies to rack
Assemblies snap on, no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from The Woodlands, TX
- Parts Used:
- 22003428
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Leg was mssing after move into new home.
Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.
Was this instruction helpful to you?
Thank you for voting!
rumbling noise
Remove dryer back,release spring tension to remove belts. Clean lint and pulleys. Replace belts,spring tension and back and LEVEL Dryer. NOTE: The back is part of the frame, make sure all screws tighten DO NOT omit any.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Cudahy, WI
- Parts Used:
- 300838
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint screen had holes
New lint screen
Was this instruction helpful to you?
Thank you for voting!
Replaced both belts.
Bought a house and inherited an ancient set of appliances. I figured that they dont make em like they use to so why get rid of them. Noticed the dryer tub wasnt spinning one day after running through three cycles. I took the back off and realized the belt that made the tub spin was broke. Went ahead and ordered both belts (old age catches us all) so i wouldnt have to order the other a few weeks later. Pulled the spring took the old belt off put on the new ones like ya would a bike chain. Used the pliers to put the spring back on and voila.
Was this instruction helpful to you?
Thank you for voting!