MDE5806AYK Maytag Dryer - Instructions

Dryer stopped tumbling, so bad belt was my first thought. Dryer is in vacation home so did not have immediate access to it to diagnose. Ordered belt and discovered that the poorly designed motor pulley had broken and the belt jumped onto the motor shaft and burned through the original belt. Week 2 after ordering pulley, installation went per YouTube video. Glad I also replaced the belt because it was brittle and cracked. Suspect it had been slipping because sheets would ball up into a log, possibly because the drum wasn't spinning fast enough. Anyhoo, after repair all seems OK.

I removed the dryer front and replaced the door switch.
Next I replaced the drum glide reassembled the dryer.

remove bottom two screws on lower front panel, remove panel. remove two screws on lower portion of door panel, pull bottom panel towards yourself to release pins at the top. Disconnect wiring for light and door switch (make sure to note what wires go where. Complete removal of front door panel. Remove 4 screws holding cylinder frame in place, lift to remove. remove remnants of old felt seal, use rotary tool to remove excess glue, etc. apply glue (used rubberized gorilla super glue), apply felt seal - allow glue to set up. reinstall in reverse direction from removal. Be sure to use glue as there are no clips or other retaining pieces for the new felt and it will not hold in place. overall pretty easy.

unplug appliance.removed 2 screws @ the rear of dryer top to tip lid back. unplugged the door switch wires.took out 3 philip screws that hold lint screen to inside of drum.removed 2 screws @ dryer front top. lifted dryer front panel off. the drum was now loose. slipped off old belt - replaced with new. set drum back into place. made sure new belt was on motor pulley & behind tensioner pulley arm. replace & reconnect items in reverse order. plug back in & test. after seeing the wear on the plastic tensioner pulley i regret not ordering that part for replacement also.

Pull broken knob off, push new knob on.

unpluged the dryer,and removed the top.
took the front of the dryer off,release the belt and removed the drum.
unbolted the idler lever.

then I put it back together.
the bolt that holds the idler lever will be a little hard to replace for some.

Early in the life of my dryer, the Cylinder Seal came out. For the past two years I put off buying the part. When it came in, I p[opped the top of the dryer, removed the two screws holding on the front panel, and pulled the Cylinder of the back wall of the dryer. I then placed the seal in the right spot, glued it down and reassembled. About Fifteen minutes of work and a cheap part, and now my dryer dries a l;oad of clothes in an hour instead of three.

Removed the two nuts at the bottom of the dryer front to be able to move the front piece. Removed three screws holding the vent assembly in place. Removed vent assembly, replaced with new part and replaced screws and nuts.

I took out the old worn out part and replaced with the one I order.

Researched problem on line. Many others had same symptums after power outages and Hurricane Irene. Dryer was in use when power went off, back on, back off than on again. Dryer would not work more than a few seconds. LED lights would go off; Drum did spin; Heater elements came on. All symptoms pointed to the control board. Replaced board and dryer is working now. Reports state that this particular control board is very susceptable to power bumps and will fail.

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

removed the bottom panel. then the door. unscrewed the 4 screws, removed duct and replaced. parts came fast and fit just right! no issues at all! I recomend Parts select as an appliance vendor for parts.

My husband got a screwdriver to open the dryer control panel. He pulled the burned control board out and put the new one in that we got from partselect.com. We tried the dryer and it worked! I took like five minutes to install. It was so easy! It saved us $130 by not calling a service technician to come over and check the machine.

No problem

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done