SDE505DAYW Maytag Dryer - Instructions

Just take the old parts with my tools and fix it, i did take the pulley bearing with care and put the new one, and adjust the screw on the motor base, the belt just was a little difficult but I did it, it's easy.

Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.

Watch the video. Very, very easy

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

Wow it was the easiest thing I have ever done.. I am NOT a DIY person.. Company wanted $108.00 to do, it cost me less than $20.00 and 2 minutes.. I have told everyone I know!!! Thanks

At first i thought i had to buy new dryer, because i did not know what to do.I said, i never done this kind of repair before, well i put everything apart and notice that the idler pulley was worn out, then i said this is something that i can fix it if i get the part. I made several calls and couldn't find it. so went in internet and found it with you.

Opened things, saw lint buildup, cleaned inside of dryer, then cleaned entire vent discharge system, put new thermal fuse back, turned on dryer and heard metal to metal, opened dryer back up, saw missing glides (both gone). Ordered what I thought were 2 glides, 2 days later 1 showed, called and was told I didn't "update" when I changed order info (parts supplier cautioned to replace 2, should only sell in pairs) so then had to wait again for 2nd glide to show up. Replaced them today and noticed dried clothes are now cooler when finished. Will note in future if clothes are warmer, clean ductwork.

Had to figure out how to open the dryer - bottom screws in front and work up, removed the drum and found the fan blade was broken. Had some difficulty removing the fanblade from the motor shaft but after that the new one was easy to install. I did need help to place the belt and drum back into place. as one person has to hold the belts on the pulley while the other adjusts the belt while putting the drum back into place.

I followed the instructions found on this site. The hardest part was figuring out how to release the clamps at the front of the dryer so I could remove the top.

The key was to unbolt the clamps at the back of the dryer first, then to use a putty knife to release the two clamps at the front of the dryer that hold the top to the front.

The rest was easy by following the steps already listed on this site and removing the two front pieces, then the drum and replacing the parts. Putting it back together was simple since I placed things in order and had taken pictures with my cell phone as I went through the process.

The time I took, included vacuuming the inside of the dryer thoroughly. Now it runs like new.

Unpluged dryer from outlet, disconnected vent, positioned dryer on side, removed screws from bottom panel, pulled pannel away from dryer body to gain access to motor. Disconnected drum belt from motor pulley, disconnected wire harness from motor. Removed motor mounting bracket assembly and placed entire assembly on floor. Removed clamps and blower assembly from old motor, installed new motor and reassembled. Very easy project, hardest part requires some trouble shooting knowledge to determine the exact cause of problem.

Removed all of the front outer bolts holding in the lower plate, front door assembly, drum outer frame and drum. While removing the outer sheel there are colored wire connections that activate the linterior light and door sensors in which I marked the interior sheel with a marker so I knew which wire went where. Before removing the drum I drew a sketch on how the belt is ran thru the pullys and around the drum, so I would have no problem reinstaLLING IT.The rooler bracket was easily removed with a socket wrench and the retaining wring was pried with a pliers. Reinstallation of the shaft, roller and ring were as simple as removal. I then cleaned the entire interior and lint basket for optimal performance. The most difficult part is pulling the belt back around the drum, but still not very difficult. Finally I reattached nall removed parts as they were removed and I now have a like new dryer for about $20.00 vs, buying anew one or repair fees costing Hundred$ OF DOLLERS.
Thanks Partsselect.com Again!

Removed lower cover. Vacuumed out. Removed black plastic vent piece. Cleaned out piece. Inspected blower motor while there. Took unnecessary photos of element wiring. Element is on lower left backwall of dryer and can be removed from the front by removal of two hex nuts and sliding downward and then out the front. I held the new and old units side by side and transposed wires and 2 components (not sure what they are - maybe thermostat) from old to new. Reassembled easily and works great - heating better than ever.

Removed bottom panel, lint vent assembly, door assembly, removed belt, drum, then heating element from back panel. Unplugged wires from heating element and put them on new element in same order screwed the element back in then all the steps in reverse order. Now I have heat when I run the dryer.
Partselect was extremely fast in shipping my order. I will shop here again!

Door switch was very easy to replace as it simply snaps in for the outside and you just clip on the two control wires that already have clips on them.

(Used joe From Beacon Falls Instructions)
UNPLUG THE DRYER FIRST
1. There are two bolts on the back of the dryer that connect the control panel and the dryer. Remove these bolts with a socket wrench and their brackets. Set aside.
2. Lift up rear of dryer top a few inches to locate two metal flanges on the front top of the dryer. Lower the back side. Now on the front of the dryer, insert the flat head of a large screwdriver (cover flat head with rag to prevent scratches) where the flanges are located and pry upward, one side at a time. It does not take much pressure until the top “pops” open. Repeat prying motion on other side of front dry to free the top.
3. The top of the dryer is now loose and can be slid backwards enough to see down the front of the dryer. Locate two screws (one on each side) inside the front panel a few inches down. Use the same socket size with wrench to remove these two screws.
4. Notice there are three wires that connect for the light on the right hand side. With care, these can remain attached. Alternately, take the time to write down the color and order and remove these now
5. Pull the front panel towards you slightly and lift up. The front panel will now come free and can be set aside. If you did not remove the wires, the front will need to be propped up close enough to the dryer so that the wires are not ripped out.
6. Remove the three Phillips Head screws located inside the dryer drum that attach the Lint Duct Assembly. Pull out the old assembly. Vacuum out if necessary.
7. Insert the new Lint Duct Assembly and secure with the three screws.
8. Reattach dryer front and top.
9. Done.