MDE16PSAYW Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gay from Lutz, FL
- Parts Used:
- WP33001793
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Closure broken---Metal piece boken
I took the clamp out of the broken piece and inserted it into the replacement part. I put the replacement into the door and screwed it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ian from Greeley, CO
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door would not stay closed because metal latch piece was gone.
I ordered the part. ( I should have ordered just in case it happens again.) When it got here it took less than a minute to snap it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Columbiana, OH
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door Catch broken
The old door catch broke and fell into the unit. Ordered the new part which arrived fast and snapped it into place. Perfect fit and the door now closes/latches correctly - like new again. Would recommend your web site to all do-it-yourselfers. Loved browsing your site, especially seeing all of the schematics and parts list for my unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Alexandria, KY
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Install new latch
Just snapped the new plastic latch into the hole (the hole was there because in trying to extract the old latch, it fell into the inside of the door). Took two seconds. Order to arrival of the part took only 22 hours!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jose from new caney, TX
- Parts Used:
- WP33001761
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
put door clip on
i order all my part from part select.com because thery are fast on my part and have good brand
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Swansea, IL
- Parts Used:
- W10169313
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dryer Didnt Turn On
First - I did some research on line as to the possible problem with this dryer.
I had already taken the front apart before, so I knew what was needed to remove the door and front.
Remove the 2 screws that hold the dryer door in place with a Phillips screwdriver. Remove the two screws on the opposite side of the door also. Place the door out of the way. The front panel of the dryer now tilts forward. The front panel sits on two clips, tilt forward and lift out of place. The door switch has two prongs that hold it in place, pinch the prongs and the switch slides out. Disconnect the two wires on the switch and connect the wires to the new switch. The new switch slides into place. I tested the new switch before I put it all back together. Took me no longer than 15 minutes.
I had already taken the front apart before, so I knew what was needed to remove the door and front.
Remove the 2 screws that hold the dryer door in place with a Phillips screwdriver. Remove the two screws on the opposite side of the door also. Place the door out of the way. The front panel of the dryer now tilts forward. The front panel sits on two clips, tilt forward and lift out of place. The door switch has two prongs that hold it in place, pinch the prongs and the switch slides out. Disconnect the two wires on the switch and connect the wires to the new switch. The new switch slides into place. I tested the new switch before I put it all back together. Took me no longer than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Worcester, MA
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door would not shut
Pushed in the Door Catch, and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bel Air, MD
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
No Power
Installing the new switch was a snap. With the dryer unplugged, open the top using a putty knife to release the 2 clips - one on each side. Lift the top and support it to stay open. Next, note the wire color and location for each of the 3 wires. Remove each wire from its prong on the bad switch by gripping the connector with pliers and pulling off. Next remove the bad switch by squeezing the tabs on the sides of the switch to release it. The switch removes to the front of the dryer. Install the new switch in the same method and reconnect the wires as before making sure the colors go back on the same prongs. I had to replace one of the connectors with a larger one (that came with the switch) since one of the prongs on the new switch was larger than the orginal (bad) switch. To do this, I cut the old connector off, stripped the end of the wire, and crimpted on the new connector. I had to be careful not to waste too much wire since there was very little slack to work with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Kirkland, WA
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
latch broke
Replace with new latch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Milford, CT
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door was not catching. The female part to the door closing mechanism broke. It was such an easy fix! Took about 30 secs to fix!!
Pulled out the broken part than easily snapped the new part into place..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth B from Hempstead, TX
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would not stay closed
I did a quick research online and found PartSelect to have the best price. I ordered my part on Monday 8/6 and to my tremendous surprise FedEx delivered it Tuesday 8/7!! I did not pay for overnight delivery. My son happened to come by that day and he took a small flathead screwdriver, pried the old one out and inserted the new part. Done in 5 minutes! PartSelect will be my supplier from now on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Kearney, NE
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Latch was broken so door wouldn't close
This was real easy just slid the latch in front panel and attached to latch assembly to the door. The repair was about 45 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from Seattle, WA
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door catch: female half
noticed that male half was in good working order, so I just snapped in the new female half; without any tools. easy repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverlee from Minneola, KS
- Parts Used:
- WP33001761
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door wouldn"t stay closed
went very well. Only took 10 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Dacula, GA
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced pressure door switch
Too simple to describe.
Was this instruction helpful to you?
Thank you for voting!