MGD7205RF0 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Travis from GARRETT, IN
- Parts Used:
- W10837240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Very loud squeaking!
Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5. I would recommend replacing all of them, they didn’t move well…..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from DINUBA, CA
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Repair video made it easy
Just follow the repair video, it was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from CAMARILLO, CA
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer was making noise - thought it was the belt, turned out to be the tensioner.
I followed the video provided by ‘Partselect’; although it was not the exact model it was close enough to get the job done with high confidence.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from MARION, KY
- Parts Used:
- WPW10359272
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Socket set
Rollers making a noise.
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from WOODBURY, MN
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lint screen was not catching lint and sending out the dryer vent
replaced dryer lint screen with new.
Was this instruction helpful to you?
Thank you for voting!
Part broken in half
Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from BENZONIA, MI
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screen ripped
Dropped new filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from CARY, NC
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Canyon Country, CA
- Parts Used:
- 279311
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
The dryer would not heat up
I first tried replacing the Radiant Flame Sensor, which was located in a tight space and was very difficult to access. I finally gave up and called a handyman to replace it. That didn't fix my problem. I needed a new igniter. That was easy to replace, but it's fragile and I broke the first one...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from MUNCIE, IN
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
dryer was making a grinding noise
I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- curtis from STOCKBRIDGE, GA
- Parts Used:
- 279640
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
replace idler pully
first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from VALLEJO, CA
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
would not heat
I started by changing the part that had the highest percentage to solve this problem , the top three didn't work , the fourth part, the disposable thermostat, and the last one that could be done from the front worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from CLIFTON, NJ
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Pulley wheel broke apart
Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WIMAUMA, FL
- Parts Used:
- W11086603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken grill
With the instructional video the repair was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Canonsburg, PA
- Parts Used:
- W10837240
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Loud squeal noise when dryer running
I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.
Was this instruction helpful to you?
Thank you for voting!