CLCE500MW0 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mike from Goldonna, LA
- Parts Used:
- 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
dryer was making a shrill noise
removed the front then removed the belt that turns the drum pulled the drum strait up from the top then removed the bushing from the back wall put the new one in I also put A little grease in the new bushing to keep it from wearing installed the drum and front. realy easy. I'm A Instructor at A technical collage in Winnfield Louisiana and I used this as A project for my students.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Jenkins, KY
- Parts Used:
- 131825900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
needed to replace drum bearing
took front panel off, removed access panel in rear to disconnect the belt from motor. removed top panel (this is a stack unit) take plastic rivets loose from lint trap, remove lint trap tube, pull drum out after slightly pulling up to dislodge drum from bearing cradle, Remove bracket and bearing from back of unit, clean parts of old grease (be carefull not to loose small ball bearing on back) Reassemble parts using moderate amount of new grease, put parts back together in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesus from Port Saint Lucie, FL
- Parts Used:
- 5304516871
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The outside vent and the duck was clogged.
I put a new lint filter,that was the problem,just open the dyer door,remove the old filter and put the new one.Fit perfect!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerry from Asheville, NC
- Parts Used:
- 5304516871
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lint basket was destrpyed
Really ,no repair;just put new lint basket in dryer;took seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Lancaster, OH
- Parts Used:
- 131825900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
worn bearing, squeaking, scraping sound
I have used this company twice now and both times have been a good experience. Would highly recommend!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from Las Vegas, NV
- Parts Used:
- 131825900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
Symptoms suggested drum support bearing was problem.
Referred to Video and replaced drum support bearing as shown. Did not solve the problem as noise was still present. Called professional repairman, who replaced the belt pulley, along with all the parts I had just installed (came as part of a total kit). I was on the correct path, but just didn't go far enough to check out the belt pulley. If it should happen again, I could complete the whole repair process. Great learning process!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Centreville, VA
- Parts Used:
- 5304516871
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My Lint Filter Had A Hole In It
I replace the filter,,,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Saint Simons Island, GA
- Parts Used:
- 5304516871
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hole In Lint Filter
Replaced ;int filter received in 3 days
Was this instruction helpful to you?
Thank you for voting!