MED6230RHW4 Maytag Dryer - Instructions

Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.

Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.

Removed the old screen and simply put in the new one

Remove old filter, throw it away, replace with new filter.

Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck

With the instructional video the repair was very easy.

first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.

Pulled dryer out from the wall and measured the distance between dryer and outlet and made the necessary cuts to proper length then installed it , moved dryer back into place . ready for clothes and no duct problems.

Lubricated pulley wheel which temporary reduced noise. This verified what was making noise. Looked up the part on partselect.com and ordered it. Recieved idler pulley with bracket in just a few days.
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and removed old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done

Pulled the back panel off with nut driver , reached in removed belt from pulley , disconnected the spring , removed the the 1 bolt holding the bracket .
Put the new one in , in reverse order . Very simple , maybe 15 minutes total . While back is off , shop vac out any lint !!

Easy manually

Just insert filter.

First I unpluged the dryer from the electical power. I removed the 2 screws holding the bottom front panel. Then I saved a bit of time and effort. Instead of removing the bracket and pulling the whole unit out, I bent the metal plate in front of the heating element toward me. I unpluged the 2 wires from the plastic casing and removed the screw holding the heating element in place. Next I pulled out the old part and pluged in the new one then connected it in reverse order and bent the plate back up to protect the element. This was a very easy and inexpensive way to fix the dryer like new again. The hardest part was vacuuming and cleaning the bottom of the dryer. There was seven years of lint build up under there.

Removed the screws holding the front cover, Removed the screws holing the heating element bracket, pulled the heating element housing out, unplugged element and removed old element. Very easy to install. The exploded pictures on website really help.

Removed front panel located hearter elemement houseing
removed screw securing houseing to dryer chasis, disconected wireing harness- be carefull here there are three lines two for the thermostat and one for the element- you only need to disconect the one nearest the front of the unit, reove the screw holding the element to the houseing it sits in and pull out. instalation is reverse the directions to remove