Models
>
MDG6400AWW
MDG6400AWW Maytag Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for MDG6400AWW
Viewing 9 of 9Manuals & Guides for MDG6400AWW
Click to downloadInstall
Installation Instructions
(0.92MB)
Manual
Owner's Manuals
(4.84MB)
Manual
Owner's Manuals
(8.18MB)
Keep searches simple, eg. "belt" or "pump".
$13.50
This OEM drum support roller kit contains the parts needed to replace one roller on your dryer. This kit includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommen...
In Stock
$30.89
This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both h...
In Stock
$14.70
This part is located on the front bulkhead of the dryer and helps the drum to rotate smoothly and quietly. If you notice a screeching or metal-on-metal noise while your appliance is operating, you may...
In Stock
$9.81
The roller shaft is also known as a support roller shaft or a drum roller axle. It is a part in your dryer that the drum rollers spin on, helping your dryer to tumble. If your appliance is noisy while...
In Stock
If your dryer is noisy while operating, or will not tumble at all, there may be an issue with the drum belt. Over time, the rubber can become brittle and snap, and the belt will need to be replaced. T...
In Stock
$44.63
This is a genuine OEM replacement lint filter for your dryer. It measures approximately 12.5 inches in length and is made of a nylon mesh material. It is important that your dryer has a lint filter in...
In Stock
$7.88
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is nois...
In Stock
If your dryer is making excessive noise, or it will not tumble, there may be an issue with the idler pulley wheel. The idler pulley wheel is attached to the idler bracket and is used to secure the dry...
In Stock
$47.91
This genuine OEM part is a radiant flame sensor for your gas dryer. It is used to determine when the temperature of the igniter is hot enough to ignite the gas. Once the igniter is hot enough, it allo...
In Stock
$13.79
This roller shaft washer is just under an inch in diameter and is used for some of Whirlpool's brands of clothes dryers.Sold individually.
In Stock
$38.35
This flat style igniter comes with a wire harness connector. This part ignites the gas within the dryer. Bracket is NOT included.
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Paul
October 25, 2023
How do I get access to the gas igniter?
For model number MDG6400AWW
Hi Paul, thank you for contacting us. We have included a video that helps you to access the igniter. The dryer in the video may appear different from yours, but it will give you a general idea of how to install the part. We hope this helps with the repair.
Was this helpful?
Thank you for voting!
Common Problems and Symptoms for MDG6400AWW
Viewing 6 of 6Noisy
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Not Heating
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
noisy rollers, broken latch
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of t
... Read more
he front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job.
Thank you.
Thank you.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from DeKalb, IL
- Parts Used:
- WP33001808
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint into venting area.
Removal of old lint collector and replace with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Monte Vista, CO
- Parts Used:
- WP33001808
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The old lint screen had a couple tears in it
No problem at all, just took out the old one in front and slid in the new one.
Was this instruction helpful to you?
Thank you for voting!