PYE3200AGW Maytag Dryer - Instructions

Finally got tired to greasing the wheels only to have to do it again so I sprung for new wheels and shafts. Popped the top open, removed the drum, installed the two new shafts with supplied screws then attached the wheels. Figured I'd change out the original belt while I was at it even though the old one still looked good. It's nice and quiet again, plus it give me a chance to clean it out.

Once we realized we needed to take the FRONT off the dryer, not the back all went well. It was an easy fix and the part fix perfectly. Instead of $60 or more for a repairman, we spent less than $20 fixing the dryer.

Open the top of the dryer, thermostat can be plainly seen. this one was obviously fried, made it easy to determine cause of problem. remove old thermostat, pins pull off posts, using socket take off nuts (hang on to the nuts), put the new on. Fixed.

first I went online and took a look at the schematic and realized that two items can shut the complete unit down and would be easy to check. First I checked the door switch with a multimeter then the high limit non-resettable thermostat. The contacts on the thermostat were open which told me it was bad. Went online to www.partselect.com and found the part really easily. came in when they said it would and it was a perfect match to the original (part numbers on the side and eveything). Make sure you correct the problem that caused the unit to overheat in the first place. IN my case the dryer air passages were full of lint. After a good cleaning put it all back together and it worked better than it has in years.

After reading everyone else's comments I started by pulling out the dryer, unplugging the power and exhaust. Next moved the dryer to an area where I had room to lay it on the back. Then using a flat blade screw driver, I popped the top attached tape to the top so I could lean back the top without having to hold it. Removed the two screws from the front panel and removed the door safety shut off before removed the front panel. Then I layed the dryer on its back. Then reached under the drum, pushed the belt tensioner toward the motor puller to release the tension on the belt. Then slid the belt to the base. Pulled the drum up and out of the cabinet. Next I cleaned all the lint and crud out of the dryer components. To remove the clips that hold the rollers in place, I use 2 small flat blade screw drivers. These are inserted at the back side of the horse show shaped clip between the shaft and the clip. When the two screw drivers are rotated like turning a screw they slide the clip out. Next I used a socket wrench with a #8 metric socket(I didn't have the sae size) and removed the screws holding the drum roller brackets. I simply reversed the procedure to install the new rollers. Since the dryer was on its back, when I put the drum back in, its own weight slipped it in place. Then pulled the belt around the drum and between the motor pulley and the belt tensioner. Holding the belt with one hand, I used the other hand to pushed the belt tensioner in and positioned the belt. Then I stood the unit back upright and put the front cover on, replaced the door safety switch, removing the tape holding the lid and then cloed the lid. Of course I put the dryer back in place, leveled it, and it now runs like brand new. My thanks to every one else who gave me hints that saved be about $450!

Very difficult for one person, trying to get the belt engaged into the motor pulley and the idler pulley at the same time. Trying to overcome the tension of the heavy spring on the idler was the main problem, while coping with the small working space with the drum in place. Solved all the problems by removing the drum (for the 3rd time) and making a piece of wood to wedge in against the outside wall of the machine to hold back the spring loaded idler. Then slipped the drum back in place and gently slid the belt around the drum. Then reached in under the drum and slipped the wood piece out while making sure the belt remained on the pulleys. If I had the wood idea at the start, it would have been about a half hour job. Good luck, and don't pinch your fingers.

Replaced the thermal shut off and the thermistor located on the heating element bracket.
Easy to diagnose and to replace- not totally accessable but not that bad either. Cleaned out lint obstruction causing the problem.

I watched the video tape

I first made sure there was power to dryer. It was ok so I unpluged the dryer from the socket and afer researching on line I was sure it was the thermal fuse. I check continuity on the fuse and it did not have continuity. So I installed a new fuse and high temp thermostat (they come together)
Just lift top of dryer up and back. In the left rear corner is the heating element. On top of the element is the thermostat. On the right side is the fuse it is a round disc with two white wires attached. The thermostat and heating element need to be removed to install fuse (one screw each and lift out of the way ) . Need to check for blocked lint or like I had the white plastic hose had a kink and need replaced with metal lint hose.

I followed the "How to" video on your web site. Most importantly, I cleaned the entire filter area which probably caused the problem as your instructions recommended. I will do that annually going forward. I would recommend your service to anyone.

1.Removed retaining clips,washers,spacer,and cylinder rollers
2.Removed and replaced support assembly
3.Installed spacer
4.Installed cylinder roller assembly
5.Installed washers and retaining clips
This is my second time ordering parts from PartSelect and I am amazed how fast I recieve my orders, which minimizes the downtime of an appliance that's frequently used.

I just followed your video how to replace a broken belt , after viewing replacing belt went easy

I suspected the high limit fuse. I unplugged the machine, lifted the top, found the high-limit fuse (about the size of four dimes glued together) just to the right of the heating coil. I pulled the two wires off and taped them together. Plugged the machine back in and it worked perfectly. I made sure the heating coils started to glow red. When the part arrived, I replaced the old unit with the new, plugged the two wires back on, and I was done. Just for additional information, when I touched the heating coil during the repair, it broke. After 16 years, the heating coils get brittle, so I also replaced the heating coil and it's thermostat just above it (about the size of 6 quarters glued together). I hope this gets me another 16 years.

Received the replacement filter which was an exact duplicate of the 22 year old filter. Took the old one out; slid the new one in and got ready for another 22 years of use. At 86 years of age I probably won't be around to see the new filter wear out. The dryer has already outlasted the place where I purchased it - Montgomery Wards! They just don't make stuff to last like this anymore.

I first unplugged the dryer. I had to move the dryer forward a little. Then I used a screwdriver to pry up the top of the dryer from the front. I positioned the top all the way back until it rested on the front of the cabinet. Make sure it's far enough back so it doesn't accidentally close on you while you are working on it. I located the high limit thermostat right above the heating coils. I unplugged the two wires going to it. I used a nut driver to remove the screw that was holding it to a bracket. I then I removed the two screws that held it to another bracket. I installed the new thermostat to the bracket and then reinstalled it to the bracket above the coils. I plugged the two wires back in and closed the lid. Make sure the dryer vent is still attached if you had to move it. The dryer works fine now and doesn't overheat.