MDG2706AGW Maytag Dryer - Instructions

The hardest part was figuring out how to access the dryer mechanism. This Amana dryer has a lower front panel that is removed and not the top. There are few instructions available for this configuration. Then the part locations do not resemble the video instructions for trouble shooting. I discovered the broken part because when fiddling with the wire connections the metal tab disconnected due to fatigue or corrosion. Removing, identifying and replacing the flame sensor was quite simple. The dryer now works as before. The dryer is 23 years old. The most time in this repair was spent figuring out how to disassemble and identify a different configuration than in the videos.

As it turned out, the felt was only part of the problem. The guide bracket had been cut thru by the drum. This all started when a golf tee got stuck in the drum area. It took very little time to destroy the guide bracket. Dryer was built by Whirlpool. Parts are built to the bare minimum. These appliances are designed to break in a couple of years. There is no doubt about it. I installed the new guide brkt, glued the new felt on and put it all back together. The job is pretty straight forward but you need to be mechanically inclined.

First of all I think this was an assembly issue, cause it was a bit noisy since we bought it, but I dismissed it as a break in noise & it would go away over time, but of course it just got worst ontil it failed....
Anyway 1st thing I did was, stick a standard screwdriver between the top & front, to pop the top off, then used a socket wrench set to remove the 2 screws for the front panel assembly, ( **taking note were what color wire connectors went were 3 for switch "y,g,b" & 2 for light "yb & g"), then used socket wrench set to remove 4 screws for the front bulkhead, ( upon removal I now understood what the noise was all about, the lip of the drum was rubbing against the bulkhead & both cylinder glide brackets, wearing the drum lip & cylinder glide brackets, down to shards of metal, rasor sharp, Both brackets were wore in half & bulkhead damaged ), then I removed the shards from the drum & used the hamer to dull & round a smaller drum lip, then I removed lint trap holder from bulkhead, ( since I had it apart I took it outside & cleaned it with my power jet hose attachment ), then I removed missalined & Damaged cylinder seal, srcapped bulkhead clean with standard screwdriver, applide goop glue to bulkhead & new cylinder seal, then applide new seal & let dry overnite, in the mean time I removed both damaged (the other half), cylinder glide brackets, used the old gliders & pads, ( they were not damaged, " LIKE NEW"???), attached them to the new bracket, then attached the 2 cylinder bracket assemblies to the bulkhead, then I used metal tape (several layers on both sides of bulkhead) to fix the damage caused by the old missalined seal & drum lip.... Then I re-assmembled lint trap holder to bulkhead, & re-assembled bulkhead to dryer, then attached the front, ( see above**), then popped the top into place... Now we have a GOOD QUIET dryer

I disconnected power and vent hose then tipped dryer on its back. I took off lower panel and door ,disconnecting wires to door and light and hanging them over the side,i then removed the front plate and felt seal the plastic fan shroud and lint trap come out as one piece along with the front plate.when i could look down on the drum,standing on the left side ,i disconnected the screw connecting the top plate to the left side plate allowing the top to gain a little play,this is the amount needed for the drum to be removed,pull belt tensioner slightly as to release tension remove the belt from motor shaft.At this point remove drum and set aside,the lower felt ring and support rollers will be exposed as well as tension spring and tension roller,i used a mirror and guided the snap ring pliers into place on the tension roller,At this point pull on rear felt ring it may come loose easy ,if not work some adhesive remover into the cracks where the glue is and keep agitating it ,eventually the glue will begin to release and more and more of the remover can get in washing the felt ring off,clean real good after using remover soap and water and allow to dry ,apply a thin ring of high heat adhesive smooth out to spread even all around when it becomes tacky begin applying new felt ring,while this adhesive cures perform the same procedure on the front panel and its felt ring while these rings are drying into place undo snap rings and pull support rollers out and replace in like order replacing thrust washers and snap rings if you damage them ,the roller on the tensioner is more tricky but if you use a mirror and a light it is easy to sneak in there lastly when preparing to reassemble and drum and belt are in place just before you replace the front panel it is prudent to replace the neoprene slides,reassemble front plate and ensure that the felt ring lines up and goes in evenly all the way around re-attach top left corner ,reinstall door and wires as well as bottom plate this will conclude the procedure i learned all of this the hard way i should have just replaced all the parts at once i was in that machine 6 different times Daniel 2017

Went on line to this sites video's to diagnose the problem. Steve Ash is EXCELLENT. Put idler& roller replacement video's in my Favorite File! Ordered parts PS11741930&PS11741913 from this site on line. Good price, Fantastic 1 1/2 day delivery (Fed Ex ) Referred to great videos for installation. Hints: 1) Be sure to identify ALL wires 2) Be careful removing snap rings from rollers, I stretched mine and had to reform them.(new ones did not come with the rollers. 3) It would be a good time to replace the belt & drum pads when the drum is out.

I just followed the video instructions and really they were not as good as some of the customer descriptions which were far more detailed. It was like an experienced repairman telling another experienced repairman how he has been doing this repair for 20 years. The customers get into the kind of detail that is very helpful. More important parts select never tells you to read the blogs first before ordering your parts. $100 later I bought a new GE dryer which I would have done 10 days ago had I known Maytag has a repetitive problem with the high limit thermal fuse which no one has a cure for. So I did a whole bunch of repairs replacing parts on a dryer which needed to be replaced.

After checking out a video showing how to change the belt I decided to tackle the job. First I pried up the top, there are two plastic tabs in the front corners that hold the top down to the front panel. The top swings upward and will stay in position while you continue to work. Using a 3/8 socket, I removed 4 bolts that hold the front panel onto the frame. Be sure to unhitched the wiring to the door switch and those to the control panel and then the front will come out by lifting it off the tabs in the lower corners. Put the front panel aside and slide the drum forward and out of the dryer frame. Remove the old belt noting how it ms oriented around the tensioner and motor pulley. Now everything should be exposed and you should take the time and clean the inside if I were you. Our dryer was filled with lint and dust but after a good vacuuming and wiping down with a damp sponge, it looked like new again. Put the new belt around the drum noting where it had sat before. There is a grove in the drum but our belt did not go inside their but on the drum itself. Slide the drum back in place and from underneath put the belt on the pulley and under the tensioner. Replace the front panel, rehitch the wires and put the top down and your done. My wife helped clean the inside which took longer than replacing the belt. Total time about an hour or so cleaning time included.

I guessed that a new belt may fix the problem. The repair was nearly as easy as the video suggested. I believe the dryer had been repaired before since there was a circular panel on the side which had been removed. I could reach in through the side to slip the new belt onto the pulley. The new belt now enables the drum to turn even for heavy loads.

I first removed the front panel and door on the dryer using a 5/16th nut driver. I needed to disconnect the light and switch to remove the door. I raised the top lid of the dryer to expose the drum. I rmover the fan schroud and lint filter by removing 4 5/16 screws with the nut driver. I disconnected the belt from the idle tension pully and removed the drum. The drum support rollers were visible on the back frame of the dryer. I removed the bad roller using snap ring pliers. After cleaning the roller support shaft and lubricating the shaft with grease I replaced the drum support roller and secured it with the snap ring. I also replaced the dryer belt although it was still workiing. I reasembled the dryer after giving the inside a cleaning with the shop vac. The hardest part was getting the belt secured with the tension idle pulley. When assemblying the fan schroud make sure it is snug against the fan so it doesn't leak. Replace the top and front door and cover connecting the switch and light. If you get the switch wires correct the dryer will run with the door shut otherwise reverse the wires.

I followed the online video on PartSelect website. No other instruction necessary.

Used a dolly to move the drier out in the garage to give myself some room to work...remove the bottom panel--2 screws at the bottom...remove the door--2 screws at the bottom of the door, disconnect the 2 switch wires and then it slips out of the top....remove 2 screws from the top and swing the top all the way back out of the way---it'll just hang there.....remove the front drum support--4 screws.....slide the drum forward while working the drive belt off of the drum.....you can now see the 2 drum support wheels.....at that time I got my shop vac and got all the lint and crud outa there......remove the snap ring on each wheel, slide off the washer and wheel, pay attention--the wheel has a front and back.....reinstall the new wheel with washer and snap ring (i put a small dab of grease on the wheel support)....I also put a dab of grease on the belt tensioner wheel support--same little snap ring retainer.....reinstall the drum by sliding it in slowly as you work the belt back into place....install the front drum support--roll the drum by hand to make sure your belt is on properly.... resecure the top, then the door, and finally the bottom....when facing the drier my left wheel was in way worse condition----this is obviously because it is located right in front of the heating element....thanx and good luck....

The dryer was squealing, so I looked videos on how to take the dryer apart. After I got it apart, I spun the roller wheels, the motor, and the idler pulley, and only the idler pulley gave an indication that it was sticking or not spinning appropriately, so I ordered the part and replaced it. And sure enough, it was the problem after all!

disassembled the entire dryer drum and front bulkhead plate. Installed belt and replaced drum on rollers and positioned idler pulley .Video was very helpful in positioning drum and belt onto idler pulley. More trouble with the existing dryer vent replacement after repairs were complete

Follow the instructions on this webside

Went to YouTube and put in good.. did not fix the problem with the dryer but it has a new belt on it now!