YMED5430PBK0 Maytag Dryer - Instructions

this was very was very easy. But I deviated from the You Tube instructions. One to release the motor pulley. I needed to use 2 adjustable wrenches for a longer lever. I needed to use a hammer to help release pulley. Second to remove the dryer cable I needed to use a small screw driver to aid in the release. ---- the part from the company was a perfect fit.

Followed simple instructions to replace two pulleys and belt. The Virtual Repairman helped me identify the cause in minutes. Took another 5 minutes to place the order and the part arrived two days later. Saved $125 at least. Thank you!

john

My dryer was running way too hot and the temperature settings didn't make any difference. Clothes were shrinking and coming out almost scalding hot. I followed simple directions posted on you tube for troubleshooting this problem. I checked that there were no lint blockages, visually inspected all connections and hardware. All seemed good. Metered out all thermostats and fuses. Everything checked good for continuity. For the reset-able thermostats, I heated them on a hot plate to verify that the normally closed switches opened near their specified temperatures. Dont do this for the non-resetable fuses and thermostats. If you're
not sure, avoid this step. Only the hi-limit thermostat seemed to open a little higher than expected but I couldn't with 100% accuracy determine the exact temp it opened. Made sure the heating element wasn't shorted in its housing or that too might give the dryer the same symptoms. That checked good too. Only thing left I could think of was to change that hi-limit thermostat. Ordered part, removed and replaced. Perfect fit. Op-checked good. All heat settings now operate normally. No more shrunken clothes that are too hot to touch even on the lowest setting lol. Hope this helps, happy hunting.

Followed instructions from video, just removed lint collector, dryer top and front panel, removed broken belt and old idler pulley. Vacuumed and cleaned up inside dryer.installed new pulley and rib belt according to printed instructions,installed new dryer duct and new clamps. Saved myself huge service call or having to buy new dryer.Will be checking with this site on any future repairs instead of calling a repair service. Your video made it real easy to repair.and I am 77 years old.. Bob

1 screw to replace.

Purchased the dryer maintenqance repair kit. Very simple to do. Easy to follow instructions. Took less than an hour. Everything I needed was in th kit. Did not have to run to home depot for anything.

Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!

The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to unthread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.

First, let me say the t videos are excellent. Check them out if you haven't already.

I came across the video on diagnosing the causes of odd dryer noises. After watching that, I decided that the issue was probably a drum roller.

I took a chance and ordered the maintenance kit to avoid having to take the dryer part to confirm the diagnosis and then put it back together again while waiting for the parts to arrive (BTW - the parts arrived within two days of my ordering them) .

Even if you know your issue is only the roller, I recommend getting the entire kit. It takes no extra time to replace the drive belt and the idler pulley while you have to dryer apart and I consider it good preventative maintenance.

Definitely watch the how-to video PartSelect provides on how to perform the repair using the maintenance kit. It's very clear and very helpful. I'm not sure I could have figured out how the belt fit through the idler pulley without it.

As video shows, the repair is pretty straightforward. As others have noted, you'll likely find a couple of dollars in change and a goodly layer of lint in the bottom of the cabinet. Have your shop back handy.

It seems kind of silly, but I found the hardest part of the whole repair was getting the front panel to slide onto the two bottom clips that support it.

One thing to watch out for are two small metal clips surrounding the screw holes at the top of the front panel. The nut screws that hold the panel in place screw into these, not the panel itself. After I struggled to get the panel in place I realized that in the process I had knocked the clips off and so had to remove the front panel again in order to retrieve the clips from the bottom of the cabinet. Minor frustration. And with all the practice I had the first time around, the panel went on much more easily the second time :-)

It was very gratifying to plug the dryer in, turn it on and have it run perfectly. Better yet, it impressed my wife.

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

We pulled the back off the dryer and we weren't sure where the problem was exactly. So we pulled off the heating element and the thermostat. The heating element seemed to be burnt out, so we ordered that and the thermostat. We got the parts very quickly, so we put them in and found that the dryer still didn't heat. There was another thermostat (trip thermostat) that we decided to order and try...bingo...that was it. Now it works like a charm.

Super easy to repair...I had to idea how to get started; but after watching the video from your site it was a breeze. Thanks for having "how to repair" videos on your site.

Repair kit came in 2 days..fantastic..thank you so much....with new rollers, belt and tension roller she works like new

Took back cover off. Cleaned out the lint that had built up inside the dryer. Replaced the lint trap housing and lint chute seals. Also replaced the drying vent hose. Works great now.

Be very careful of burrs on the edges of the steel inside the dryer. I cut myself badly when reaching into unplug the switch.
Procedure: Lifted the dryer top by pulling forward and rotating front up. Removed 2 philips screws holding the switch at the door. Reached into dryer and unplugged bad switch. Inserting small blade screw driver at the edge helped release the plugs detent. Installed new switch using reverse of above.

It's amazing... I fixed my dryer!! I am a 47 year old woman with no technical training, and I did it!

I live in a apartment and I bought the Whirlpool Dryer (Model #LER7646JQ0) USED for $150 about 6 months ago. The dryer started blowing cold air, so I called the place that I bought it from and they quoted me a price of at least $300 to fix the dryer.

After searching through google, I found the partselect.com website, and read the repair stories. I decided to take a chance. I ordered just 2 of the suggest 4 parts that could fix the issue, and the dryer did not work. The next day I order the other 2 parts, and that did it - my dryer was fixed.

The diagrams on the site were a little confusing to me (the dryers looks a little simpler inside) but it was easy to repair. I used a screw driver and plier to do the repair, however it would have been much easier if I had a socket set. I would suggest buying all parts suggested, and return the items you don't need. Here are the parts I used:

1. THRMST-FIX (Thermostat, High Limit 221 F
2. USE WPL 279838 (Heating Element (10" long x 6" wide)
3. Thermal Cut-Off Kit
4. Cycling Thermostat (Limit: 155-25) (Thermostat, Internal-Bias)

Good Luck!