Models > YMED6230HC3 > Instructions

YMED6230HC3 Maytag Dryer - Instructions

Jump to:

All Instructions for the YMED6230HC3
106 - 120 of 332
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Robert from CALIFORNIA, MO
Parts Used:
661570
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Broken belt
Disconnect gas line and vent hose,removed top and back covers to install belt.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from WOODBURY, MN
Parts Used:
W10120998
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
lint screen was not catching lint and sending out the dryer vent
replaced dryer lint screen with new.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from SALLISAW, OK
Parts Used:
WP3387747
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Heating element went out.
Followed the instructions all went good except for the sliding the shield back in it didn't want to go back in but it does fit. Dryer works like new again.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from MUNCIE, IN
Parts Used:
279640
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
dryer was making a grinding noise
I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
braulio from FORT WAYNE, IN
Parts Used:
WP3387747
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Not heating up
I just took the old element replaced with the new one i order from this site, I save some money was really easy so proud of my self...
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rory from LEESBURG, VA
Parts Used:
WP8577274
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Dryer kept throwing the E1 error indicating the thermistor needed replacement
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cindy from BENZONIA, MI
Parts Used:
W10120998
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Screen ripped
Dropped new filter in.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donna from CARY, NC
Parts Used:
W10120998
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rod from YORBA LINDA, CA
Parts Used:
WPW10446781, W10837240, 661570
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set
Loud Dryer
Please do not buy parts from Parts Select. My order was not shipped the next day (as advertised on the web site), but instead 3 days later. I paid an extra couple of dollars for expedited shipping, which did made no difference (except for a couple of extra dollars for Parts Select to pocket).

When I emailed customer service to complain, I never received any response. I can't believe that customer service can be so unimportant in such a competitive marketplace. And with the power of social media, you would think customer service would be a big differentiator.

I ended having to buy another part (the igniter). I found a different vendor with better prices and a commitment to satisfying customers. I got my part in 3 days for cheaper shipping than the starting point of Parts Select shipping. So I guess I should thank Parts Select for forcing me to look elsewhere because I found a better place with better prices and better shipping and better customer service!
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Douglas from Galway, NY
Parts Used:
WP3387747, 279973
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Broken heater element
From the front, removed lower panel, tilted machine back at a 45 angle for ease to assess heater. 2 screws, removed old one .. hint. Take a picture of the wires,, Slide new one in,, I also changed the two thermostats while I was in there,, just because.. maybe a 1 hr job
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Terry from TIVOLI, NY
Parts Used:
661570
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Dryer belt so old it slipped and would not turn drum
Seemed daunting but pull the front off and the drum is basically just perched inside on some rollers. You have to pull it out to really reach in and wrap the 96”+ band around it and to motor and don’t forget to tension it with tension pulley if you don’t see that if your belt broke!
Another bonus is after 10 years I got to remove the softball size fur ball rolling in the squirrel cage fan , big help on air flow!!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edwin from PASADENA, TX
Parts Used:
279640
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Idler pulley broke off.
Took back panel off, and it was really easy putting the new idler pulley in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from WIMAUMA, FL
Parts Used:
W11086603
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Broken grill
With the instructional video the repair was very easy.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Canonsburg, PA
Parts Used:
W10837240
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Loud squeal noise when dryer running
I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
DW from ALVIN, TX
Parts Used:
WP8577274
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
F-26 Fault message
Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the YMED6230HC3
106 - 120 of 332