MGD6230HC3 Maytag Dryer - Instructions

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

I started by changing the part that had the highest percentage to solve this problem , the top three didn't work , the fourth part, the disposable thermostat, and the last one that could be done from the front worked.

I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.

With the instructional video the repair was very easy.

The hardest part was figuring out how to access the dryer mechanism. This Amana dryer has a lower front panel that is removed and not the top. There are few instructions available for this configuration. Then the part locations do not resemble the video instructions for trouble shooting. I discovered the broken part because when fiddling with the wire connections the metal tab disconnected due to fatigue or corrosion. Removing, identifying and replacing the flame sensor was quite simple. The dryer now works as before. The dryer is 23 years old. The most time in this repair was spent figuring out how to disassemble and identify a different configuration than in the videos.

Removed the top, front cover, drum and belt. Removed the idler pulley bracket and pressed the frozen pulley from the shaft. Cleaned the shaft and applied a small dab of anti seize and replaced the pulley. Installed all parts in reverse order. Dryer works like new again.

Looked it up on YouTube. It told me to take the front panel off. I did, changed the belt, put the panel back on and it works perfectly. The part came in the time it was supposed to and it was the correct part. Thanks.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.

Remove old filter, throw it away, replace with new filter.

Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck

Lubricated pulley wheel which temporary reduced noise. This verified what was making noise. Looked up the part on partselect.com and ordered it. Recieved idler pulley with bracket in just a few days.
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and removed old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done

Unplug unit turn off gas, remove only bottom front panel first tried radient flame sensor was not the problem it was the coils which were infront easy to acess with small screw driver remove two prong coil and replaced then the three pronged coil being sure to line them back before tigtening left off cover and watched for ignition once it turned on and ran replaced cover and done.

Pulled the back panel off with nut driver , reached in removed belt from pulley , disconnected the spring , removed the the 1 bolt holding the bracket .
Put the new one in , in reverse order . Very simple , maybe 15 minutes total . While back is off , shop vac out any lint !!

Just insert filter.