MED8230HC0 Maytag Dryer - Instructions

As per directions (videos) I found on PartSelect; 1st removed the bottom panel, then removed the housing (2 screws) covering the fan/lint trap area. Pulled the wires (2) from the heating element and removed three screws, 1 on the side of the housing immediately behind the heating element terminals, and 2 screws holding the stamped steel riser in place. I didn't have to remove the entire heater housing, but rather wiggled the heating element out slowly. For that I used a pair of pliers to grip the element and a gloved hand to hold the housing steady while I pulled one side then the other. I spent some time vacuuming out all the dust while I was in there. Replacing the element was a little easier, it slid in with firm hand pressure. Then just a matter of reversing the steps above. Wife was happy and once again, I am a hero.

I watched your online repair video, which was excellent. As I started the repair, it was exactly as described in the video....very easy. The only thing I did differently was clean out the mechanical compartment of the dryer with a shop vac.....simply because it was full of lint. There is nothing I won't try to fix; but this job can be done by anyone. Do it yourself; don't spend the money to have someone else do it.

Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!

Removed toe plate, make sure and use something like a 5 in 1 painters tool, makes the job easier as you will see a notch inside the seam between toe plate and outer shell, take 1 screw from heater tube cover I used a nut driver, this job is best to use with a stubby socket set, there are 2 machine screws with hex heads holding the heating element to the heating tube, you cant really see the heads but can feel them with your fingers, disconnect the 2 terminals in front of this, but make sure you use a blue or black sharpie to mark the terminals, use your stubby and remove screws, then use a set of needle nose pliers and pull out the heating element, the new heating element slide right in the grooves then reverse the take off process, good luck

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Took bottom accesses panel off dryer (two screws). To the right was heating element housing. Three screws to remove inside. One at the bottom of houseing bracket (holds up heating element housing) which connects to dryer cabinet floor. One at top of bracket (connects to bottom of heating element housing). One on the left side where the elements wires connect (screw goes through housing then through element side arm). Once the three screws are removed disconnect wires and pull element stright towards you. Once everything was diasembled I took shopvac in side machine and swept it all out. Just reassble the same way you took apart.

Opened the bottom section removed the heater element replaced it and boom!! It works!!!!!

I ordered the Part on Wednesday night, it arrived on Saturday, and was installed by Monday by my husband. This was the best service I have seen in a good while. Kudos to you!

Disconnected dryer from power source. Removed bottom panel on dryer. Removed three screws. Disconnected two wires on heating element. Pulled heating element out. Attached new heating element. Success!

first turn off the power supply then ..removed the lower front cover. .removed the heat shield that covers the element. .. removed the element and replaced with the new one ..

It was very easy to repair and the 1-800 number is a grat resource for assistnat in locating the part.

I opened up the bottom of the cabinet and found some evidence of burned lint in the heater box. I ohmed out the thermostats and they were good. Then I ohmed out the heater coil and found that it was an open circuit.

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.

Followed the instructions from the Whirlpool Technical Service Manual available online

Being from the old school where we never assume to know what the problem was, so took out the heating element to inspect which I found that the element had a broken coil which confermed my suspicions. I ordered a new element on Saturday from paRts select on Saturday and recieved it on Wednesday Ann the rest was a matter of reassembling which was a breeze since I foot plenty of pictures.