YMED6600TQ0 Maytag Dryer - Instructions

pushed the broken catch into the door and snapped the new one back in. Works perfectly!

Opened the cabinet and removed the drum. Cleaned out the dryer fuzz. found that the roller stabilizer wasn't in place; apparently due to a previous repair. Replace both rollers and the roller stabilizer and prepared to replace the drum. But because I live alone, I didn't have anyone to hold the drum while I connected the belt to the motor. But, I did have three unused balloons which I partially inflated and set the drum on them in the bottom of the cabinet while I hooked up the belt to the motor. Put everything back together and it is now drying my clothes again. :)

Watched the video, followed the printed instructions for reminder when necessary. Needed a second person briefly to hold the dryer tub when installing the new belt, and also when removing/replacing the front panel. Beyond that, it was straight forward and relataively easy to do. Solved the noise problems and it dries more evenly now as well. The one thing the instructions don't say is to check the rear canvas seal when the tub is re-inserted into place to assure it doesn't fold back on itself.

I first unplugged the dryer and pulled it away from the wall. I had to remove the vent tubing to gain access to the rear of the unit, then removed the screws on the back panel of the dryer. I took off the panel and noticed that lint that had gathered over the years around the back of the dryer. I vacuumed it clean then proceeded to problem solve. I noticed four easily identifiable areas, the thermal cut-off switch and thermostat located by the heating coil and the thermostat and fuse near the venting area. I first checked the fuse with a ohm meter, it was okay. I removed each component one at a time and created a bypass with a alligator clip wire. Plugged the dryer back in to determine if heat was produced while testing each area one at a time. I determined that heat was produced after bypassing the thermal cut-off switch. I then ordered the thermal cut-off switch kit (arrived within 3 days) and installed it within 20 minutes. The longest time spent was trouble shooting, the removal and installation was very easy. By the way, I did use the ohm meter to check the resistance across the thermostats as indicated in previous postings, but I found the results and technique to be more confusing. A bypass worked the best for me and much more reliable. The heat started immediately. I highly recommend downloading the schematics of your unit for part number and location identification.

replaced rollers, belt and pulley. Video was very helpful

flipped up the top pulled the front off easy access to drum removed the drum replaced rollers per instructions that came with package. very eas job. works great.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Took a screwdriver and bent wings out a little and then was able to get hold of it with a pair of pliers. Then just put the new unit in the opening and tapped it in. If I had a good pair of needle pliers, it would not have been necessary for the screwdriver.

followed the enclosed instructions, used a balled up towel to support the drum while attaching the belt and tension pulley, took about 20 minutes

Did not take the door off..applied adhesive and seal fit perfectly..used packaging wide tape to secure for a bit while adhesive dried..waited 24 hrs..holding well..dryer is back to working order..thank you..I received the seal in 2 days after ordering!!

Looked up on the internet, saw a video, ordered the part using model of dryer, got the part in 7 days, took out old part and snapped in the new door latch. Now it works good as new

My son did the repairs it took less than 30 minutes it's an old dryer so glad to be able to get the parts. I do not like the new dryers because of all the pushbuttons thanks so much for the ports

I shorted the thermal cutout after removing the back.
I then ordered the thermal Cut-Off Kit from PartSelect.
While this was not my first order from them, I was still impressed with the ease and by how soon I received the part without any hassles or glitches. PartSelect will be my primary parts supplier from now on.

I bought a new thermo cut off and replaced the old one.

I placed the putty knife on the top part of the door catch and when that came loose I placed the putty knife on the bottom of the door catch and pushed on the putty knife and the door catch came out of its place. I then just popped the new door catch in place. Total repair time 45 seconds. The door now closes.