MEDP576KW0 Maytag Dryer - Instructions

Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip.

Be very careful of burrs on the edges of the steel inside the dryer. I cut myself badly when reaching into unplug the switch.
Procedure: Lifted the dryer top by pulling forward and rotating front up. Removed 2 philips screws holding the switch at the door. Reached into dryer and unplugged bad switch. Inserting small blade screw driver at the edge helped release the plugs detent. Installed new switch using reverse of above.

It is odd that this part needed replacement but I am in an area near the Atlantic ocean in a vacation house which is vacant most of the year. The exhaust vent probably brings excessive moisture down to the dryer in the basement. The screen you can see at the inside back of the tumbler (where the heated air enters) rotten out, pieces fell inside and there was danger of something falling in and catching fire. I found no useful source for information (including YouTube) as this part is most easily replaced from the rear of the dryer and the available info was about repairing the heating element, the circuit board, or the exhaust venting pieces which is done from the front.

The bottom line is that the back removes easily. You should:
1. unplug and remove the exhaust shoot
2. remove the top per YouTube or other source
3. take off the back panel over the electrical connections and unscrew the ground; tuck it inside. Don't undo any electrical connections except the ground
4. take off the screws holding the back on (8-9, one is hidden above the exhaust vent) and pull it out of the way; you then have compete access to the "DUCT-AIR" part
4. undo the clip that holds the vent tube (from the heating element) to the part
5. remove the screws that hold the part to the inside back (3?) and push it out of the way
6. remove the clips and remove the old part
7. reassemble in reverse order

I'm over 70 so I took lots of time and breaks but was still done in under two hours. The 2 clips holding the heater element tube to the part were badly rusted and should have been replaced but I made do with the old ones.

You tube video for info. Using a multi-meter check for resistance on thermal fuse. it was open. take a picture of electrical component wiring before disassembly or draw a picture then mark wires with numbers to identify position. Before starting make sure to unplug the power cord. Have to remove the back cover 8 screws, Also it was suggested to replace the thermostat so i did. It may have caused the over heat condition. Replace the 2 parts,3 mounting screws and 6 wires. Put it back together and tested it. Dryer now works.

had to take front off of Dryer then was able to replace drum roller

Replaced power cord, terminal block, and all melted wiring. Checked the thermal fuse for zero resistance.

On this model do not try to remove the back. You must remove the bottom front panel and the lint screen unit. You can then loosen the heat coil assembly and rotate it to get to the high-limit thermostat and the thermal unit. I replaced both because I bought the kit. It actually took me longer to clean out lint than it did to replace the parts. A simple remove of the parts with a 1/4 inch nut driver did the trick. Now my dryer works fine.

Replaced the heating element. Took the front lower panel off, 2 screws one on each end, removed cover on left side over blower 3 screws and removed cover lower right side over heating element 2 screws. Removed 6 wires plugged into heating element cover, turned heater element cover counter clockwise and pulled out. Removed 1 screw holding heating element inside of cover, pulled out heating element. Replaced heating element back in cover putting screw back in to hold it. Put heating element and cover into hole in back of dryer turning clockwise to secure. Then put cover holding heating element over the front of it and secured with 2 screws. Put blower cover back secured with the 3 screws and put the front cover back on securing with 2 screws. dryer is heating better than ever.

Just replaced the old lint filter.

I called an appliance repair company to do a diagnosis and was told the timer would need to be replaced. Parts and labor was quoted at $290. The dryer isn't worth that much. Found a video on this site on how to replace a timer for my model of dryer. Ordered the part for $116 and replaced it myself. The video instructions were exact step by step.

Just like the video, just followed the video
Thanks,

After checking the temperature safeties, I replaced the Push-To-Start switch. This did not solve my problem, so I replaced the Timer Switch assembly, which did solve my problem. Both switches are very simple to replace. Unplug the dryer, use your nut driver to remove the 6 screws holding the back control cover. For the Start switch, remove the control knob, remove the 2 screws holding it it. Unplug the wires, turn the switch housing 1/4 turn clockwise, and remove it from the opening. Reverse the process to install the new switch. For the Timer Assembly, just a bit trickier. Remove the knob, remove the 2 screws holding the assembly. Unlike the Start switch, the Timer Assembly has multiple wires. Pull the old timer assembly out, and, one-by-one, move wires from the old Assembly to the new Assembly, being sure to land them on the proper post. Once you have done this, return the Assembly to the mounting hole. A very simple repair. Even though I spent $160 chasing the problem, I still came out cheaper than calling a repairman.

Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.