SDG3606AWQ Maytag Dryer - Instructions

I looked at your on-line diagrams (exploded views) and basically used them as dis-assembly info.

I removed the bottom panel, followed by the front panel, the drum holders and drum.

Toughest part was the spring clips holding the motor in place,,,, but notes on your site from other folks doing the same motor replacement solved that one,,,,,, I used a flat bladed screwdriver and pliers to manipulate the clips both off and on

First I removed the bottom front cover attached with two screws, then the main front cover attached with two screws. I then removed two more screws holding the top in place, detached three wires and raised the top lid. I held the top lid out of the way with a cord tied off to a cabinet above. I then removed four screws holding the front support panel in place and set it to the side with wires still attahced. Then I slid the dryer belt off the drum and removed the drum. Next I removed the cover of the fan wheel by removing several screws. This allowed me to unscrew the fan wheel (reverse threaded) by anchoring the motor shaft with a wrench and using a large socket to turn the nut end of the fan wheel (then was no snap ring). I then popped off the two clamps holding the motor in place and removed the motor. The only tricky part about assembly was putting the belt back on the pulleys once the drum was installed. You can't see the pulleys once the drum is installed so it is done by feel.

Removed 2 screws from dryer lower front panel and removed panel. Then removed upper front panel (no screws, just clips). Removed screws from existing duct assembly (2 for the duct assembly and 3 that held the top of the assembly to the dryer opening (and the reason for removing the upper front panel). Original part was a two piece assembly, new one is a single part, using less screws. New part is also deeper that original assembly. There was enough room for the extra size. Installed new part, replaced top 3 screws, top panel, and bottom panel. The replacement was very straight forward. Anyone that has done this before could do it in a few minutes but without prior knowledge or a manual, it took a full 1/2 hour to do the replacement.

First and Foremost i was told that my problem was with the Thermal Fuse (Fix Ya.com), Then with the little Electrical knowledge I have thought Fuses don't turn on and off,If the fuse was bad i would get No Heat. (Even for a second) Fuses just don't turn on and turn off intermittently,when they go there done! So after a little research i decided to order the gas coil valve. I tilted the top up, two screws on the front panel, took that off and the valves were exposed,(bottom left) two screws too remove bracket then installed new coils on bracket,put back together and I Have Heat Again! NO problems what so ever since new install. I would say having not been for cleaning lint build up inside the machine (been 6 years) the Whole project took me Ten Minutes.

The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.

First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--

Opened things, saw lint buildup, cleaned inside of dryer, then cleaned entire vent discharge system, put new thermal fuse back, turned on dryer and heard metal to metal, opened dryer back up, saw missing glides (both gone). Ordered what I thought were 2 glides, 2 days later 1 showed, called and was told I didn't "update" when I changed order info (parts supplier cautioned to replace 2, should only sell in pairs) so then had to wait again for 2nd glide to show up. Replaced them today and noticed dried clothes are now cooler when finished. Will note in future if clothes are warmer, clean ductwork.

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

First I unpluged the dryer, removed the two screws from the bottom access panel. I used a small socket to remove the screws securing the limit stat to the burner chamber, nut driver was too long.
I installed the new limit stat with the two screws and attached the two leads. Plugged in the dryer and conducted a test run, burner ignited. I turned the dryer off and replaced the access panel.

After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!

I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.

Good trouble shooting information.

Replaced coils on gas valve.

Had to figure out how to open the dryer - bottom screws in front and work up, removed the drum and found the fan blade was broken. Had some difficulty removing the fanblade from the motor shaft but after that the new one was easy to install. I did need help to place the belt and drum back into place. as one person has to hold the belts on the pulley while the other adjusts the belt while putting the drum back into place.

Unpluged dryer from outlet, disconnected vent, positioned dryer on side, removed screws from bottom panel, pulled pannel away from dryer body to gain access to motor. Disconnected drum belt from motor pulley, disconnected wire harness from motor. Removed motor mounting bracket assembly and placed entire assembly on floor. Removed clamps and blower assembly from old motor, installed new motor and reassembled. Very easy project, hardest part requires some trouble shooting knowledge to determine the exact cause of problem.

Remover broken part with needle nose pliers and replaced knob. Less than thirty seconds.