YE20EN1 Magic Chef Dryer - Instructions

I removed the lint trap then the dryer cover from top and front side. I placed the belt around the dryer drum being sure to put it on the correct side with the grid side against drum. I coiled the belt around the pulley and motor tract. Replaced everything in opposite order in which it was removed.
Video from website was very informative and helpful. I was able to follow along step-by-step to replace the dryer drum belt. I am officially a do-it-your-selfer!!!

I took the back of my dryer off to see if the problem was there. I saw that the belt was broken and laying on the inside of the dryer. Took belt and went on line (Google) my KitchenAid Dryer from it's model number. The website was PartSelect. Found the belt I needed and saw a video on how to replace the belt. I called to order the belt and spoke to Steve, which help me with all my needs. Steve knew just the belt I was looking for and placed my order. The belt arrived a few days later. While I was waiting for the belt to come in, I removed the front of the dryer and get ready for reinstall. It took me about 15 minutes to install the belt and put the front of the dryer back together. I found PartSelect to be very helpful and saved me, maybe $150.00 by not having to call a serviceman to do the easy replacement. Thank you Steve and PartSelect, now I'm number 1 with the wife again.

First, I unplugged the dryer. I pulled up the lint filter, then unscrewed the two screws there. Then pulled up the top panel. I had a helper hold it up since it couldn't lean against the wall. Then I had to take the front panel off the dryer. The idiots at Kenmore used screws, not pins, so I needed to use a socket wrench to get those two out of the top corners. Then I lifted it up and off. I removed the broken belt. I put in the new one. I replaced the pulley, which had fallen without the tension of the belt holding it in place. It was pretty easy to figure out how it went, but I consulted the online community for a diagram. I threaded the belt in place, replaced the panels, and viola! It worked. Easy.

The dryer was not difficult to repair. The diagram that came with the belt made the repair easy. The repair part came in a very timely manner.

I replaced it

Step 1. Read all the comments about how to do this job in this forum. (i found them very useful)

Step 2. Read the directions that come with the dryer (they helped a lot)

Step 3. Don't forget to disconnect the power cord before reattaching the door switch wires (oucH! ) or doing anything with your dryer.

Removed the two screws holding in the Filter and removed the filter.

Removed the two screws holding the front onto the dryer.

Put the belt over the drum and proped the drum up.

Reseated the tension spring and pully in the proper slot. (On my machine it is the position closest to the motor).

Reassembled the dryer in the reverse order.

-Took top of by prying with screwdriver.
-2 screws and door wire to take off front panel.
-proped drum with 4X4 piece of wood.
-looped belt around drum where the mark for the old belt was.
-looped belt through tensioner and pulled with the screwdriver over the motors drive shaft.
-manually spun drum to make sure everything was right.
-put panels back on and was done.

You cant go wrong with the included directions and belt diagram. this is the first repair I've done of any kind that went flawless.

Disconnect the power and gas supply so that you can slide dryer out and into an accessable area to work comfortablely. Removed top and front of dryer. When disconnecting numerous wires from the top controls, draw a simple color coded diagram for reconnection before you disconnect those wires. After removing the top and front, take out the drum and clean all the lint, money etc. out of the normally nonexcessable area of dryer. Place new belt on as you replace the drum. This takes two people; one to hold the drum in position and one to carefully work the new belt into place. Rotating the drum by hand will assist in the placement of the new belt on the drum. After reassembling the newly cleaned dryer it was a pleasure to try it and find a dryer that worked better than during its pre-repair use and it saved us the price of a repair call or a new dryer.

first, i read all the comments on this web site as well as other web site. sooner i confirm the problem is the drum belt, i order the parts.
my kemore model front panel is one piece. so i have to lay down the dryer and open the front panel on the top. The instruction sheet sent with the belt is very good, so it does not take too much time to replace the belt, the challenge task is to reconnect the front panel to the side panel. I spend too much time trying different way to use the fastner hook to connect panels without realizing that the hook is broken. stupid me. i later have to use the wire to connect the front panel to side panel. overall, i am very happy i fix the dryer.

Remove back panel, looking for access. upon reassembly dropped socket into lint trap. Dissemble again, also dissemble lint trap ducting, found it almost completely blocked by lint, clean and reassemble. Remove front panel and there is the problem of the broken belt. Try to look up online to no avail because I didn't have the proper machine ID, but I did find out where to look. Now with the right info ordered the part. Received in the post about 5 days. Upon reassembly I realized that the adjustor was laying in the bottom, picked up, cleaned inspected, OK, then needed to figure out where it goes, got it, then to figure out how it holds tension on belt. That took a few minutes, well maybe 10 then the old Ford light bulb came on, then installed the belt and adjuster. Replace front panel, slide back into place, hook up wiring and duct. Test, guess what folks it works.

With no experience repairing appliances, I did figure it out that the drive belt was broken since the motor was running and the drum did not turn.

What to do? Start looking for fasteners! I knew I had to get to the drum, but there was nothing up front, on top, or bottom that gave a clue. Only the back panel had hex head steel screws. I removed them and the panel. Then I removed a tube that pulled air from the drum to the outlet. I saw some screws holding the back of the dryer top. After removing them, the top popped off by pulling it up and releasing the attachment at the front.

This gave me access to a couple of screws holding the top of the front (holding the door). It seemed to make sense to lay what was left of the dryer on it's back. After removing the last two screws at the top corners of the front panel, I pulled it up and removed it. The drum lifted right out. The belt tightener was loose and lying against the back wall.

The local Sears did not have a replacement belt and their web site was not that helpful or forgiving. A Google search revealed a site called PartSelect. It had a very useful search routine which led me to make a purchase on a Saturday evening. The belt arrived at my door on the following Tuesday! Be sure to look at the instructions that come with the belt, it will demonstrate how to fish it through the loose belt tightener.

In about 1.5 hours the dryer was back together and doing it's thing. There were two additional screws left over, but I figure that's a manufacturing defect.

I was a hero to the wife, as usual.

Pry up front of top and lay back. Remove two 1/4" srews at top corners. The front of dryer will then swing to the right. The drumb will lift out easily. Remove broken belt. Inspect the drum rollers on the back wall. Replace if loose or not turning. Mine needed replacement. The assembly part is not easy. You need the drum in place and after it is in place you can't get the belt on. After 8 tries I got smart and made a prop to hold the idler pully up, then put the belt in place and let the pully down slowly. It worked! Put the front back on and the 2 screws and pop the top back down. Also it is a good idea to unplug the electric cord and turn off the gas (if app).

Took the top off then front off of the dryer with just 2 screws( thank god not the back) and replaced the belt...had a difficult time getting the tension pully in place, belt kept falling off..the stop screw for the tension pulley was bent ,so had to replace that first.

I googled 'replace dryer belt' and found instructions on the 'Virtual Repair Man' web site. After reading the instructions through twice I began.

First I removed lent filter and removed the two screws that hold the lent body in place. I rotated the top panel up and back and leaned it on the wall; proped up the dryer drum with some scrap wood pieces; rotated the front panel of the machine out enough to slip the new belt, groves down, around the drum; reinstalled the idler pulley under the drum; raised the drum slightly and reattached the front panel. Reattached the top panel and replaced the filter. Did a test run and worked good.

I got a price from Sears for the part and they were asking $45 just for the belt. I saved enough in parts and labor to take my wife out for a real nice dinner. thanks