DG20F5AM Magic Chef Dryer - Instructions

I first unplugged the dryer. I had to move the dryer forward a little. Then I used a screwdriver to pry up the top of the dryer from the front. I positioned the top all the way back until it rested on the front of the cabinet. Make sure it's far enough back so it doesn't accidentally close on you while you are working on it. I located the high limit thermostat right above the heating coils. I unplugged the two wires going to it. I used a nut driver to remove the screw that was holding it to a bracket. I then I removed the two screws that held it to another bracket. I installed the new thermostat to the bracket and then reinstalled it to the bracket above the coils. I plugged the two wires back in and closed the lid. Make sure the dryer vent is still attached if you had to move it. The dryer works fine now and doesn't overheat.

Grown daughter did the repair following instructions on your site........Unplug, take screws out of top by lint filter and with putty knife pry up top panel and lean back. Unplug elec. harness in front corner. A screw on each side of front panel removes that. Get old belt off and then we vaccumed all the lint from under and around drum. Put new belt around drum making sure not twisted and pull pulley as shown to make tight......... would have taken less time but we vaccumed all the lint from under and around the drum. Anyone could do this......

Checked out the coil seemed ok. So I replaced the radiant flame sensor. No change. Then I replaced the High limit sensor still the heat was not staying on. I read some were in the troubleshooting guide that the coil can test good, but can still malfunction. So that was it new coil fix it, works like a new Dryer again.

First I removed the screws of the dryer cover. Next removed the screws holding the dryer drum.

Drilled out the two rivets left from the old glide. Inserted the plastic and postitioned the cushion underneath. Inserted the new glide and drilled a hole in the plastic to accomodate the new rivet. Inserted rivet. Pulled the other end so it was tight holding the cushion and did the other end. Done.

Had to cut the glide 1/4 '' of the width to slide it through the existing slots in the panel.

I just followed your video how to replace a broken belt , after viewing replacing belt went easy

I suspected the high limit fuse. I unplugged the machine, lifted the top, found the high-limit fuse (about the size of four dimes glued together) just to the right of the heating coil. I pulled the two wires off and taped them together. Plugged the machine back in and it worked perfectly. I made sure the heating coils started to glow red. When the part arrived, I replaced the old unit with the new, plugged the two wires back on, and I was done. Just for additional information, when I touched the heating coil during the repair, it broke. After 16 years, the heating coils get brittle, so I also replaced the heating coil and it's thermostat just above it (about the size of 6 quarters glued together). I hope this gets me another 16 years.

the video was very well done and able to understand. disconnect power ,remove lint trap,remove 2 phillps head screws, push putty knife in front seam line about 1'' in from corners to release top assembly ,lift up and support, disconnect wire connector ,remove 1 screw in each front corner lift front panel off while holding drum, remove broken belt,install new belt with grooves against drum ,feed around tensioner pulley and onto motor shaft pulley ,spin drum by hand to make sure belt tracking etc. reassembly in reverse.

I unplugged the dryer from the outlet and opened the top of the dryer with a puddy knife .I marked both wires "T" for the one on top and "B" for the one on the bottom. I removed the screw that holds the bracket in place that the High Limit Kit fuse is attached to and removed both wires with a pair of pliers. I made sure that the new fuse was turned the same way as the old fuse. There is some writing on one side and it should be pointing to the back of the dryer. I put the fuse in the bracket and placed the bracket back in the slotted holder placed the screw back in the bracket holder tighten it up hooked the wires up as labeled and closed the top. I plugged the dryer up opened the door and the light came on. After I turned it on it worked then it tripped the breaker. I reset the breaker turned it on again and it worked I haven't had a problem since. Make sure that you use the fuse with the pink dot on it for a electric dryer.

I opened up the dryer lifting the lid with a putty knife and removed the two screws holding the front. I reached in and removed the belt and removed the drum. I took my shop vac and cleaned all the lint, the door passage to the lint screen extremly full of hard lint. I tested the coils with my multi meter and they tested bad. I also did the test that was suggested by Part Select and again it showed the coils as bad. Once I received the parts about three days, it only took about twenty minutes to install using just a screw driver to replace the coils and the belt went on real easy with easy access to the tentioner. and my dryer now runs more quiet and dries the clothes in half the time it used to take. My belt was still in pretty good shape but I put a new one on since I had it apart any way. My friend had the same problem with his dryer and spent $300.00 for a repairman to do the same thing. I tried to tell him it is not rocket science and very easy to do yourself. Thank you Part Select for the good repair advice as well as the timely delivery of the parts.

I just removed 1 screw that held the safety thermostat in and replaced it. Then I removed the long screw that holds the heating element and the high limit fuse in place. Replaced the fuse, cleaned out the lint duct area. Closed the dryer lid and pluged it in, it worked fine.

Lifted top from dryer and fuses were in the back of drum just below heating coil. Used nut driver to remove heating coil to gain access to fuses and replaced them. Process was quick and easy. Diagram from this site made locating fuses elementary!

P.S. I have no certified experience in appliance repair.This was my first time ever and dryer works perfect.

I took apart the dryer by unscrewing the top and the front, front comes off by just undoing the two top screws on the inside. I figured it was something to do with the rollers since the noise was ciclycal. The hardest part was to put the drive belt back on. It helps to have a second person for about 5 minutes.

i followed part select instructions that probable cause was either thermal fuse or high limit thermostat.put ohm meter across both & saw thermal fuse(has pink dot on it) part 53-1182 was open.ordered thermal fuse replacement kit. part#LA-1053. the problem i had was after reaching down the side of heating housing removing the bracket with the thermal fuse,replacing & reconnecting it i had a hard time reinstalling the bracket,very tight space & i don't have very big hands.finally got the fuse in it's hole in the bracket & slid & jammed the bracket into the side of the mounting housing & it stayed secure.dryer started

We took off the front of the dryer and saw how the new belt needed to go on. It took myself, my daughter, and my husband to get the belt in place and the drum aligned. Once that was done, I put the front of the dryer back on, this holds the drum in place. After that, we sealed the back of the drum like the instructions stated, turned it on, and it worked. We were a little concerned with the instructions stating if the drum was not sealed properly it could cause "fire & death". We kept checking the dryer throughout the evening... no fire, so we were very happy to have done this repair ourselves. Thanks. I would not have tryed it myself except for the positive comments on your site when I looked to order the part. They were correct, it was easy to do and saved us a lot of money in repair service. It also showed my 23 year old daughter how easy it is to some things yourself. :)

I tilted the unit back enough to scew the new legs into the threaded holes.