Models > YE20FY4C > Instructions

YE20FY4C Magic Chef Dryer - Instructions

Jump to:

All Instructions for the YE20FY4C
91 - 105 of 521
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Miguel from Hollywood, FL
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Broken dryer belt
I followed the posted directions from others, and it was a breeze. They were really helpful. I would just add the step of keeping the drum in place with a block of wood underneath before removing the front. Slip the belt around the drum, reattach the front , and then finish positioning and tensioning the belt once the block is out of the way .
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
sheila from east lansing, MI
Parts Used:
341241
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
I heard a noise when I opened the dryer, took off the front panel and saw the broken belt on the floor.
We took off the front of the dryer and saw how the new belt needed to go on. It took myself, my daughter, and my husband to get the belt in place and the drum aligned. Once that was done, I put the front of the dryer back on, this holds the drum in place. After that, we sealed the back of the drum like the instructions stated, turned it on, and it worked. We were a little concerned with the instructions stating if the drum was not sealed properly it could cause "fire & death". We kept checking the dryer throughout the evening... no fire, so we were very happy to have done this repair ourselves. Thanks. I would not have tryed it myself except for the positive comments on your site when I looked to order the part. They were correct, it was easy to do and saved us a lot of money in repair service. It also showed my 23 year old daughter how easy it is to some things yourself. :)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from McAllen, TX
Parts Used:
341241
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
broken belt on dryer.
lift top of dryer unscrew the top of the pull out filter from the top of dryer. then unscrew the screws near top on the inside of the front panel and have an old soap container handy to hold up the dryer drum. lift the front panel up for removal and put the old soap container under the drum to keep it from falling out. Then mess around with the idler pulley and look up information under pictures of idler pulley in place with belt in Google to see how the belt fits through it.. Finally replace belt, check front and back of drum to insure proper fit and put the dryer back together to see if all works well. and see if the reason for belt breaking is apparant and more than just old age and use.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOAN from BIG PINE KEY, FL
Parts Used:
341241
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Tub Would Not Spin
First, I printed one of these responses which were excellent and very detailed. The screws connecting the lint slot to the top of the dryer was frozen. Taking the front panel off was difficult because I did not read the instructions I printed out very well. After I took the top off I had a hard time finding the 2 screws located inside on the top of the front panel. They are located to the far right and left at the top. To take off the front panel you have to push it up to release the clips on the bottom, then it comes right off. Taking the drum out was easy. What was difficult was putting the belt on. There wasn't any slack and to put it around the pulley and the drum for me was difficult. After that is was a piece of cake. It works great.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RICHARD from BOYNTON BCH, FL
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
dryer belt was broke
i pop the top of the dryer lose and removed the 2 screws that held the front on and installed the new belt and put it back to gethere
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Andrew from Ballston Spa, NY
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set
Broken dryer belt
I went to repair the dryer belt only to realize that it was jumping off the pulley(edge was worn away). If you are replacing the belt, make sure your pulley is good before you order your parts. I ended up having to go to lowes and make a pulley!
Works great though.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
oliver from moss beach, CA
Parts Used:
LA-1008
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set
noise and vibration getting louder over an extended period of time
The repair was much easier than anticipated. Next time I could do it in less than 30 minuites.

Replaced the axel that holds the rollers as well as the rollers. Just rotate the left one 90 degrees and it slides out.

Probably what took the most time was puting the belt back on. It is old so I was being careful. It took a couple of trys to keep it on the rollers as I moved the drum into position. So easy I am convinced to buy another Maytag.

Wife was impressed so that's worth something!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ruben from Basprop, TX
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Drum would not turn, but machine had power.
Before ordering the part, I found this website by linking from a video on YouTube where several people showed how they did it. Simply two screws in the lint removel chute and pushed in the two clips holding the top and two inside screws holding the front panel. Held the machine tilted back onto a table and placed two 4" wooden cubes underneath it so it wouldn't come forward and one more 4" cube under the drum. After cleaning out the inside, I slipped the new belt around the drum (ribbed side down) and taped it in place with a couple of pieces of painter's tape temporarily. Hooked the idler wheel guide and looped the belt in it. Tested movement by spinning it by hand to check alignment and removed tape. Reassembled the front, side and top panels accordingly and tested it. Voila! This was my first attempt and I saved myself some bucks. The last repair was done by Se•rs and their service person took my credit card number for the invoice and promptly went out and charged over $3,000 on it. He was eventually caught. Great incentive to do yourself, huh?
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robbi from PowderSprings, GA
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
The dryer would not tumble
I watch the video and played it again while I was working.
I am a 54 year young woman and I did it.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Penants Harbor, ME
Parts Used:
341241
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
The belt broke
I replaced it
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Linda from BURSON, CA
Parts Used:
WPA3167501
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Light bulb went out in mictowave
Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jim from BEAUFORT, NC
Parts Used:
341241
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
dryer belt parted
Raise the top and then remove two screws to remove front. Once the front was removed on this Maytag model it was not necessary to remove the dryer drum. I simply lifted the drum slightly and slid the belt around the drum to position the belt. I then pressed the tension arm toward the drum and fed the belt around the drive pulley and tension pulley. I spun the drum a few turns by hand to insure that the belt was aligned properly. Then replaced the front cover and the top. Turned on the dryer to test and job was completed. Thanks to your video and prompt parts delivery the job was a snap. My wife didn't even have time to get mad.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Angie from Hiddenite, NC
Parts Used:
341241
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
belt broke while drying clothes
The dryer was not difficult to repair. The diagram that came with the belt made the repair easy. The repair part came in a very timely manner.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Erika from Swarthmore, PA
Parts Used:
341241
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set, Wrench (Adjustable)
Dryer drum wouldn't turn
First, I unplugged the dryer. I pulled up the lint filter, then unscrewed the two screws there. Then pulled up the top panel. I had a helper hold it up since it couldn't lean against the wall. Then I had to take the front panel off the dryer. The idiots at Kenmore used screws, not pins, so I needed to use a socket wrench to get those two out of the top corners. Then I lifted it up and off. I removed the broken belt. I put in the new one. I replaced the pulley, which had fallen without the tension of the belt holding it in place. It was pretty easy to figure out how it went, but I consulted the online community for a diagram. I threaded the belt in place, replaced the panels, and viola! It worked. Easy.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Allen from Valrico, FL
Parts Used:
341241
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Broken belt
It was easy to remove the lint trap first, then the front dryer panel. The drum easily was removed and installing the new belt was a little tricky because the belt had to be mounted onto pulley while holding the drum in place. I had a little help from a friend to help me stabilize the drum as I placed the new belt. Once on, it was easy to re-install parts in reverse and have dryer working again.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the YE20FY4C
91 - 105 of 521