CYG3004AWW Magic Chef Dryer - Instructions

I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.

I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.

She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.

When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis

ordered part 1 day & it arrived the next!
just fit right on...saved cost of repair man!
very easy!

No Repair, just replacement. Went perfect.

Watched youtube video to problem shoot. Cause determined to be coils bad. Searched web found Parts Select to be easiest site to deal with and had coils for best price. Followed instructions supplied with parts. Dryer works like new.

took 2 screws out and replace new coils

I ordered the top 5 items that may cause this problem based on the troubleshooting guide presented by the technicians I found in youtube. I replaced the coils and that fixed the problem. The coils are the first to go out according to techs, but I have the other parts just in case I may need them later on. My Maytag dryer which is over 19 years old is alive and working again. The coils are accessible from the bottom access panel secured by 2 nut screws, unplug the dryer first, then the coils are secured by a bracket with 2 small philips head screw, I used a stubby philips screw driver to remove the bracket, undo the 2 electrical connectors on the coils one with 2 prongs and the other with 3 prongs. Put the new coils attached the electrical connectors and secured them with the bracket. Checked for any loose wiring ensuring connectors are secured in place, then test run the dryer with the panel off so you can see the if the flame stays on, if you run the dryer without wet clothes the flame may stop after 15 or so minutes. It is better to test run the dryer with wet clothes just like when your drying fresh washed and wringed clothes. It was really easy, good luck!

Found on your site the top two causes of a Dryer not getting hot enough and ordered those parts ( which were delivered quickly).Removed the top two screws that hold the front of the dryer that gives access to the coils and flame sensor assembly after lifting up the top.It took more time to clean up all the lint than to replace the parts.Dryer works great!

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

Really an easy fix. 2 5/16" screws hold the cover on below the dryer door. From here it's easy access to the gas element. 2 more screws for the valve cover and disconnected the attached wires to the gas coil valves. slip the news ones in place, re-attach the wires and install the holder.Tested the dryer and it fired right up. Put panel back in place and the wife is happy it didn't cost us more than just the parts. Yep, she's a lucky girl. ;0)

I popped the top off and tipped the dry over . It took 2 to reposition the drum and belt back after taking it out and remving the old wheel and replacing it.

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

As many of the other posts here on this website mentioned, I had the same problem of the dryer not heating up. I removed the front panel (4 screws on each side inside of door - easy - followed instructions) and once off I was able to view the igniter glowing properly so I knew the starter/igniter was not the issue. Everything I read then suggested that it must be the two terminal gas valve coil, and sure enough it was. Ordered part -- got it in literally a couple days -- removed bracket (two screws) put in new coil -- turned it on -- works great. Could not have been easier. This is a great website and would recommend it to everyone who is a Do It Yourselfer.

I just used screw driver to pop of clip put new roller on poped clip back on

i read some of previous customer problems and fixes pulled the front cover off found coil's location when i turned on drier you could see the ignitor getv hot but burner would not ignite unless i put a little pressure on secondary coil when i let go of coil flame would go out. ordered 'M' series new style coil kit came in in about three days installed parts drier workng good i would reuse parts select agian thanks

removed the lens cover, replaced the bulb and reinstalled the lens cover.