YE20EY1 Magic Chef Dryer - Instructions

The repair was much easier than anticipated. Next time I could do it in less than 30 minuites.

Replaced the axel that holds the rollers as well as the rollers. Just rotate the left one 90 degrees and it slides out.

Probably what took the most time was puting the belt back on. It is old so I was being careful. It took a couple of trys to keep it on the rollers as I moved the drum into position. So easy I am convinced to buy another Maytag.

Wife was impressed so that's worth something!

Belt was broken Removed the front (very easy) removed the drum. Noticed the roller was damaged. Replaced the roller. Installing the belt was tricky but followed an on line video. This dryer has the motor and tensioner behind the blower housing. There was not enough room to use both hands effectively. So first I placed the belt on the motor then pulled the tensioner until I could slide the belt on the tensioner with my other hand. This was the reverse order from the video. The dryer now seems to be quieter.

Followed the instructions and the repair went like clockwork, took less than an hour. I spent more time brushing and vacuuming old lint from the innards of the machine than I did doing the actual repair. Finished up $0.78 richer, too, from the change I found inside the machine.

Was a little hard getting at the idler pulley being it was behind the blower assembly, but it was the only draw back.

Shut off power and gas, unscrewed lint vent, raised top on angle with rope, unscrewed and moved door switch, unscrewed and took off front, put new belt around drum, then raised front end of drum with 4 narrow pieces of 1" foam insulation which let me view and install the belt connection to the drive motor shaft, adjusted the level of the drum using the rope holding up the top, removed foam pieces, replaced and rescrewed the front to fit the drum front channel, replaced the door switch, replaced the top and screwed it to the lint vent, returned gas and power, and ran confirmation test.

Pretty much just followed the video - I'd never opened a dryer before, so I'd watch a step, pause and do it, then run the video a few more minutes, and repeat. These dryers are really extremely simple devices: just a heater, then a motor to spin the drum and run the fan (I think the same motor does both). So you loosen a couple of screws, pry the metal case open, and slip on the new belt. Done! I didn't keep track of time, but I'm psyched to have saved myself a $200 repair call! Standard delivery arrived in less than two days, just like they said it would.

First thing was to disconnect power to the dryer. I lifted the top lid and found 1 screw on each side at the top near the front and removed them. I also removed the door switch (CLIPPED ON) leaving the wires connected to the actual switch. Then the front panel lifts up and outward. I was able to install the belt from the front, guiding it back to the pulley/idler arm. Reassembled and it worked great. The belt I bought from this site appears to be better than original stock. It should last a long time. :)

First I had to find my way into unit . I took out screws that didn't have to come out, but eventually I found my way in. I took out the drum put the belt over it and through the tightener then over the motor pulley. I then put the sheet metal back on and the job was done.

first pryed up the dryer top, pulled the two wires for the door switch and removed front panel. remove 8 or 10 blower housing cover 1/4" screws. removed blower moter shaft snap ring pulled out damaged blower wheel. slid on the new wheel with the flats on the shaft and new wheel alighned up. installed blower clamp around blower stub. installed motor shaft snap ring. reinstalled blower cover cover. installed front dryer cover to include installing door switch wiring. put down top and pushed dryer back into place making sure to install the blower vent hose. started dryer to test operation. all worked well the first time.

Remove front panel of dyer, pry open with srew driver,be careful not damage enamel. Remove drive belt, pull drum forward and out. Drum glide are located at bottom of drum rest,rollers at rear of dyer.

When the dryer drum stopped tumbling, I followed the instructions on PartsSelect to remove pop the top of the dryer and then remove the screws to remove the front panel. Then I could see the broken belt underneath the drum.

I did pull out the drum itself to get a better look at the motor and pulley to see where the new belt would need to go. I replaced the drum by pushing it back and then rotating it so it would fit back into the groove on the rear panel.

Once I received the new belt, I followed the steps included with the belt package to loop the new belt around the drum and then thread it over the pulley and around the motor.

The entire repair was very easy and so much cheaper than buying a new dryer.

Tilt dryer top. Inspect damaged part(s). In my case it was the high-limit thermostat; but since the dryer is old, I ordered the heating element kit. The thermostat is included. Disconnect wires from thermostat and remove. Disconnect wires from element and remove. Carefully install new element and reconnect wires. Same for thermostat. Dryer works fine. Also, delivery time was one day. Thank you Partselect.

First of all let me begin by telling you that this was my first D-I-Y project. The dryer had been out for over a month and the clothesline drying of clothes, while being energy efficient, did not go well because it was the summer/fall borderline and the ants and bugs were inside the clothes which were brought into the house.

I googled my problem and soon enough there were a ton of helpful sites available offering solutions to my problem. So, after I decided to do it myself, I ordered a new belt from part-select. Once the belt arrived, I went back to for help. There was an extremely useful video among the results. The whole thing took me about 20 minutes as I was doing it all by myself. I followed the steps and was able to replace the dryer belt very easily and I am so very thankful to have a working dryer again before the onset of rain and cold!

First I removed the back panel (and found out later when I received the belt from Partselect.com, that this was unnecessary). I followed the instructions that came with the belt and removed the top panel and then the front panel. I placed a piece of wood under the drum for support so that it would not be just hanging from the back. Then I found the broken belt lying on the bottom, and a pulley that was unhinged. I replaced the pulley following the instructions, and vacuumed the motor and all around. I put the new belt around the drum and then through the pulley and onto the motor axle. I replaced all the panels and the dryer is now working like new.

I followed instructions here on this site, and repaired the dryer with ease. More details in other posts but it pretty much went like this:
1) take out screws under lint thing, lift top
2) take out two INSIDE bolts in the top of the dryer (5/16" socket), disconnect wires, lift then set aside front
3) clean everything out, set dryer on it's back.
4) wrap belt around the tub (rubber facing the tub), and then loop it through the tensioner (which will have fallen out of place, but you can see from the wear where it goes). Note it loops through the tensioner then over the motor wheel, and then back through the tensioner. Took me a little while to figure that out. (put tensioner in place before doing the looping through)
5) put it all back together.
Very satisfying to have it all work again!