YE204KAC Magic Chef Dryer - Instructions

1st thing,,,,unplug dryer from electric,,,Raised the top of dryer, took 2 screws out that held front of dryer on, removed 3 wires and dropped front of dryer. exposed blower wheel,, removed all nuts holding front of blower wheel, removed clamp on front of wheel with pliers, removed old wheel, replaced everything in reverse.

First I removed the screws that held the part in place, but this proved to be the hardest part for me. I had to find the right kind of screw driver . It was not a slotted or Phillips. It was more star shaped. Once I had the right tool, the rest was pretty easy.
I then opened the top of the dryer to be able to lay the front on the floor. There were wires connected to the front, however, so I had to remove the part that the wires were connected to by slipping it out of the bracket that held it in place. Once the front panel was on the floor, I simply lifted the old part out and placed the new part in. I closed the front, replacing the part with wires back into the bracket, locked the top down tight, replaced the screws, and I was finished.

unplugged the dryer.
opened it up.
unscrewed the housing that was holding the blower wheel.
removed the broken blower wheel.
placed the blower wheel on the shaft.
got a socket wrench and an extender to tap the blower wheel into place. I put a towel over the socket wrench so as to be gentle on the blower wheel. I tapped it down until I could fee the grove on the shaft where the washer used to go to hold in the old blower wheel (the new one has enough grip on its own to stay put).
put the housing back on after doing a few spin tests to make sure the blower wheel was spinning freely.
did some spin tests after putting the housing back on.
reassembled the dryer, plugged it in.
turned it on to test again.
done.

First off I want to say I ordered my motor on Sunday night at 11:30 PM on veterans day and got the two day delivery. My part was sent out on that Monday (fed. holiday) and I received it Tuesday around 1:00 pm after I disconnected the wiring harness, took the blower fan C-clips off, unscrewed about 6 screws, and pulled the assembly apart I just done everything in reverse and replaced the new motor. I discovered that my thermostat fuse was blown so I ordered the High temp thermostat kit from here (two day delivery) on Wednesday at 10:30 PM and got the parts Friday at around 2:00 PM. After taking out four screws and four wires I replaced the fuse and high temp. set, pushed the start button to see if it worked and it started up like new. Now it heats twice as fast and everything doesn't have a light burnt smell. So dry time is faster (no more 80-90 min. cycle times), less dryer sheets (to cover smell) and all this added up to cost savings on electric bill and dryer sheets. It took a week to get my dryer back (because I just looked at the motor) but in the end I needed the fuse and motor. The quick turn around time to get the parts, the pictures to see if I had the right parts, and the ease of ordering the parts meant only one run to the laundry mat, and that wouldn't have happen if the dryer hadn't messed up on laundry day.

After reading the comments of on-line customers, I realized the dryer opens like the hood of a car and then you pull the front of the dryer door off in order to get to the two screws holding the old lint duct housing unit. Putting the new part on was easier, but I would have appreciated a detailed picture along with the written instructions. Thank you for your quick delivery. Kathleen Yosso

Was obvious what the problem was when dryer lost heat. Thermostat was fried with one contact burned off.
Unplugged dryer
Opened top of dryer using putty knife to release latches.
Removed 2 wires to Therostat, and removed the old one (2 1/4 hex screws).
Installed new thermostat, and reconected.
Done

Open the lid, replaced the small fuse on top( one wire at a time). Removed the heating element, then replaced the lower fuse and re-installed the heating element. That part of the job took 15 minutes. The fuses were blown because the plastic housing inside of the front panel was completely clogged. I took the two screws off holding the front panel on, then the two torque screws on the plastic housing. I cleaned a ton of lint out of the housing and re-assembled.

First lift the top and remove 2 screws holding the front panel on, at each top corner. Release the door switch from its clip (or disconnect the wires). Remove the front panel by tilting out and then lifting it up off the bottom tabs. Remove the belt from the motor by releasing the tensioner. Then lift the drum out. Remove the front blower cover, then remove the tensioner by first removing the spring, then pull the tensioner out toward the back. Remove the strap on the back of the motor near the pulley. It takes a little effort to get the strap off. Remove the 3 bolts holding the blower case (with the motor still attached. Remove the motor wires, then lift the motor and blower case out. Next remove the clip holding the blower fan on and remove the fan. It may be stubborn so be patient and slowly work it off. Remove the next clip behind the fan. Then remove the motor from the blower case by turning it counter clockwise (as viewed from the motor side). Installation is the reverse.

My dryer stopped cold one day, we rushed out and bought a new one. Stuck with a broken dryer I thought I'd take a shot at fixing it (with zero experience). After a few minutes on the internet I found out that a clogged vent can cause it to overheat and blow the fuse. I opened it up and sure enough it was 100% clogged. I replaced the parts that came in the kit and after about 20min it was running like a champ. Now what do I do with the extra dryer?

The repair was relativley easy. Had to remove the top, it popped up with a screwdriver and picked it up and leaned against the wall. Then removed two screws to remove the front.Removed old belt then move dryer tub forward, removed bad roller bearing, installed new bearing,applied some grease ( had to use a screwdriver to pry bearing pin off/on which is reusable.Finally installed the new belt around tub, the most trickey part since there was no access panel, but after a few tries it was easy to figure out.Great price on items and i checked several places,quality parts and delivered only a couple days after i ordered. I highly recommend partselect. Thanks Kirt

The support roller broke and that made the noise as the rubber came off the wheel. It took about 8 months before the belt finally broke. Since I had it apart I decided to change both the drum felt seals and idler pulley wheel. I had trouble finding high temperature adhesive for the drum felt seal. Lowe's and Home depot didn't have anything that indicated it would take the heat. Finally located an adhesive at a craft store and the label claimed it was good on washers and dryers. Although I was able to glue and stretch the felt onto the dryer by myself if you have two people it will be alot easier. My dryer had made so much noise for so long I couldn't believe how quiet it is now.

Unplugged electric, turned off gas valve. Opened top using a putty knife, laid it gently back against the wall for support. Removed 2 screws holding front on-leaned front out about 3-4 inches- while holding front with my knees I disconnected door switch wires.-then removed front panel. Followed instructions on maintenance sheet glued on underside of dryer top (Lucky it was there). Took tension off drive belt. Removed belt and drum following instructions on lid sheet. Removed old slides (worn out) Installed new pads & slides. Vacuumed out all lint/dust/dirt I could reach, Cheked rear drum rollers. Reinstalled everything that I had removed. It took extra time to do everything because dryer was in tight space, little working space. Turned gas on, plugged in electric cord. Worked great now.

Quick fix it works
remove the two screws holding the top from the back. Pull out the top section with the knobs
You should now be able to see the high limit fuse and the heating element.
Remove the two screws holding the fuse to the dryer. Replace the fuse and test before covering.
Also clean up the heating element with a soft brush or blower.

Actually, I was the handy man. First I removed the front panel. Then I used 3 - 2x4s to hold up the drum. Then I slipped the belt around the center of the drum ,motor,and around the pulley at the bottom of the dryer. That was it, and then I put it back together. My wife was amazed and proud that I did it without calling for help! No Problem!

I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.