CYE3005AKW Magic Chef Dryer - Instructions

I removed the dryer front and replaced the door switch.
Next I replaced the drum glide reassembled the dryer.

A friend did the repair for me. Very simple. Saved me a lot of money by getting the parts and fixing the problem. Thanks!

Dryer stopped tumbling, so bad belt was my first thought. Dryer is in vacation home so did not have immediate access to it to diagnose. Ordered belt and discovered that the poorly designed motor pulley had broken and the belt jumped onto the motor shaft and burned through the original belt. Week 2 after ordering pulley, installation went per YouTube video. Glad I also replaced the belt because it was brittle and cracked. Suspect it had been slipping because sheets would ball up into a log, possibly because the drum wasn't spinning fast enough. Anyhoo, after repair all seems OK.

The video on the web-site was very helpful in showing how to take it apart. First we remove the power plug from the wall outlet. Then we used flat scrapper to push the top two hidden clips to release the Dryer's top. We used the nut driver to unscrew the two screws that held the front panel. We carefully remove the wires that were connected to switch sensor for the door, and the lights. Next step was to unscrew couple more screws that held the front piece from the main fan housing. At the bottom locate the tensioner of the belt. Release it. Remove the dryer drum with the belt. We took the opportunity to clean off the lint that was all over on the bottom of the dryer. We then could reach the bottom left back of the dryer to unscrew the screws that held the heater unit. Before that we unscrew and release the wires for the Thermal fuse and the limit thermostat which are all located on the heating unit. Then we replace with new pieces. Upon removal of the heating unit we noticed the broken heating element. Next was to place the drum back in. We made sure that the drum lined up with the rear support piece then the front. We rotated the drum just to make sure that it was sitting correctly. Then we screwed the front housing unit. Then we put the front panel back on the hooks at the bottom. That help to line up the front panel with the main chasis. We connected all the connectors to the right terminals. Last was to set the top down on to the chasis. We checked that the duct in the rear is not obstucted. Lastly was plugging in the power cord and testing the dryer. It is working again. Thanks to Part Select's video and parts. Total time was just over half an hour.

unplug appliance.removed 2 screws @ the rear of dryer top to tip lid back. unplugged the door switch wires.took out 3 philip screws that hold lint screen to inside of drum.removed 2 screws @ dryer front top. lifted dryer front panel off. the drum was now loose. slipped off old belt - replaced with new. set drum back into place. made sure new belt was on motor pulley & behind tensioner pulley arm. replace & reconnect items in reverse order. plug back in & test. after seeing the wear on the plastic tensioner pulley i regret not ordering that part for replacement also.

I had already taken the dryer apart prior to changing the felt seal. Had oiled the rollers, greased the bearings & vacuumed the whole inside of the dryer out. Had used a high temp lubricant on the seal & had stopped squeaking for about a month. I ordered 2 seals & when they arrived, I popped the top of the dryer off using the putty knife to pry the spring latches. I opened the top up & leaned it against a wall. I disconnected the wiring to the light & the switch in the door, making note of the wiring order. Then used a nut driver to take the 2 screws from the inside out, that holds the front cover in place. Then the same for the 4 screws holding the front bulkhead in place. Then lifted up & out from the unit. Then used the putty knife to scrap the adhesive & old seal off the bulkhead. Cleaned as much of the adhesive off, then applied some high temp silicone adhesive to the bulkhead, placed the new seal on, using some clamps to hold it in place. After making sure it had adhered to the seal & bulkhead. Did the reversal of the above mentioned steps. Moved the unit to laundry room, plugged it in then started it & voila no more squeaking dryer.

Very simple repair. Remove front panel, door, drum etc. Try to keep everything seperated, screws etc. I put lockjaws on the back to get the nut off the front. Make sure to check the housing for "melted on" blower wheel residue. Easy enough to remove. I checked with my local parts dealer he wanted twice the price and needed to order it (at least a days wait). PartSelect sent the exact same part in a day and a half. Put everything back the same way I removed. Hardest part is the drum and belt. While you have everything apart don't forget to clean the thermastats etc. PartsSelect was quicker and cheaper.

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

This is a real easy fix to do by yourself. First, I removed three screws on the inside of the dryer. These hold the air duct assembly in place. Second, remove two bolts on the front-bottom part of the bottom panel. Third after panel is removed loosen the two other bolts and remove air duct assembly. Simple as that.

Make sure to unplug the power cord.Pry the front,top of the dryer up with a screw driver. Carefully disconnect 3 wires and remember where they go, top right. Remove 1 top bolt on each side of the front cover, inside.Pull up slightly and towards towards you to remove the front cover. Disconnect the light wires if applicable and remember where they go from the front drum support. Remove 4 bolts on the front drum mount cover; the lint catcher will come off with it. If needed, pull up and towards you on the drum to lower the it off of the guide rollers to allow slack in the belt. Reach under the drum, raise the idler lever, slide belt from under the idler lever pulley, remove the belt from the the motor shaft. Carefully remove the drum. A 7/16 wrench and ratchet can be used to remove the idler lever from the mount. Remove idler lever from the spring. Reverse these steps for installation of the new idler lever. For installing the belt, actually fold the belt and put it under the idler pulley and back onto the motor shaft. The idler lever should sit on top of the belt when on properly. Make sure the belt is lined with the wear area of the dryer drum. Roll the drum manually, counter clockwise several times to help insure belt alignment before reconnecting the wires and re-installing the front cover and top. A belt replacement will not require removal of the drum.

Idler was the noise source. Drum support rollers were failing also. I almost spent $500.00 on a new dryer, glad I replaced the parts instead. Sounds and works like new. Watch the video,its very helpful. Thanks Parts Select. You should advertise your services on TV or radio. I am glad I found you.

My son n law took the fron off the dryer, whilw I looked on the inertnet to locate whatever part we would find to be in need of. He pulled the front panel off and the drum out to dicover it was the bracket and glide. They were easily replaced by popping the bracket out and snapping th new one in then placing the guide on it proper spot.

My son will discribe how he did the repair.
First I opened the top, then I removed the front with a 1/4 inch ratchet and socket. I took the cover off the blower housing with a nut driver. Used the appropriate socket and a 1/2 inch ratchet, and an adjustable wrench to hold the motor shaft and removed the Blower wheel. I replaced the broken Blower Wheel and put all it back together.
Our dryer is now working great and there are no unwanted sounds emanating from within. We are very happy with PartSelects promptness and that we recieved the correct part as ordered. PartSelect website was easy to navigate. We plan if the need arises to do so again in the future.
Thankyou Frank and Rodney

ordered new knob but I had to request a return of the part I received as the arrow on the new know was opposite of what it should be -

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!