YE20FY2 Magic Chef Dryer - Instructions

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.

Just slid the new filter in.

Watched a video and went to town taking it apart. I stuck a pop can under the barrel to hold it up while I worked on pulleys. My dryer does not have a plastic pulley but a metal tension bar with a hole in the middle. Ran upstairs and watched a different video with my set up and all was good. 5 min of work 5 min watching Youtube and 5 min cleaning all the lint out of the machine. I am actually glad the old belt broke because some of the lint was in a clump and had scorch marks on it. I took the shop vac to every part of the cabinet and shoved it down the lint trap sleeve also.

Needed a belt. Only snag was for me was re-installing front panel (door)

I replaced it

First, I unplugged the dryer. I pulled up the lint filter, then unscrewed the two screws there. Then pulled up the top panel. I had a helper hold it up since it couldn't lean against the wall. Then I had to take the front panel off the dryer. The idiots at Kenmore used screws, not pins, so I needed to use a socket wrench to get those two out of the top corners. Then I lifted it up and off. I removed the broken belt. I put in the new one. I replaced the pulley, which had fallen without the tension of the belt holding it in place. It was pretty easy to figure out how it went, but I consulted the online community for a diagram. I threaded the belt in place, replaced the panels, and viola! It worked. Easy.

- Unplug the electric dryer.
- Manually opened the top of the dryer.
- Unclipped the wire assembly attached to the front panel of the dryer.
- Removed two screws holding the front panel of the dryer, and remove front panel for access.
- Very Important!! Note how the old dryer is currently installed before proceeding.
- Rotated the dryer drum while working the dryer belt toward the rear of the dryer.
- Removed the dryer drum.
- Removed the old dryer belt.
- Put the new dryer belt around the dryer drum and put the dryer drum back onto the drum rollers and into the rear guides.
- Here's the hard part, lay on floor and reach into the pulley area and motor - wrap new dryer belt around these belt rollers as "noted" in the fifth step.
- Rotate dryer drum by hand to ensure the new dryer belt is exactly installed as the old dryer belt.
- Reinstall front panel.
- Reclip wire assembly onto the front panel.
- Manually close the top of the dryer.
- Plug in the electric dryer.

Step 1. Read all the comments about how to do this job in this forum. (i found them very useful)

Step 2. Read the directions that come with the dryer (they helped a lot)

Step 3. Don't forget to disconnect the power cord before reattaching the door switch wires (oucH! ) or doing anything with your dryer.

Removed the two screws at the back that hold the top of the dryer. Then I pried off the top at the front by inserting a screwdriver into the front to remove the top from the clips. Then I tilted up the top like a car hood.

I removed the two screws inside that held the front on and lifted the front off. Because of the wires attached to the front, I made sure to turn the front aside without pulling on the wires. After removing the broken belt, I put the replacement belt over the front of the drum, lifting the drum a little. Then I threaded the belt over the drive and around the tension wheel per a diagram I found on the web.

While I had the front off, I removed the lint trap and cleaned out probably decades worth of lint.

Then I replaced all the parts in reverse order, plugged it in and had a working dryer!

DISCONNECT THE POWER. Double check the dryer is unplugged. Use a putty knife to free the latches holding the top of the dryer in place. Lift up the top of the dryer and secure it in place (be sure it's safely held open and won't come crashing down onto yourself as you work). Remove the two screws on the inside and near the top of the dryer, which hold the front and side panels. Gently lift up on the front panel (it may help to open the dryer door to get a better grip). Once free from the bottom clips, carefully rotate the front panel so that the door sensor wires are not strained. Once the front panel is out of the way, grab the drum and firmly lift it up and away from the back. (The drum has rollers and ridges at the rear and you'll need to pull the drum out of its "track"). Slide the new belt around the drum and position the drum about halfway inside the dryer. Loop the belt around the motor, but not the tensioner, (it will be easier to install the drum if you wait to tension the belt). With the belt around the motor, gently slide the drum back keeping the belt around the motor pulley. Press and guide the drum back onto the rollers at the rear. Check the belt is positioned correctly around the drum and motor. Reach back from the front and loop the belt around the tensioner. Rotate the drum by hand and make sure the belt is aligned and the drum spins smoothly. Position the front panel and slide it onto the lower clips. Install the screws being very careful not to drop them into the abyss... Close the lid and plug in the power.

First let me say that the video provided was wonderful, I followed the instructions on the video, & it worked great, no problems at all. Saved me from paying huge costs from a repairman.

I took the back of my dryer off to see if the problem was there. I saw that the belt was broken and laying on the inside of the dryer. Took belt and went on line (Google) my KitchenAid Dryer from it's model number. The website was PartSelect. Found the belt I needed and saw a video on how to replace the belt. I called to order the belt and spoke to Steve, which help me with all my needs. Steve knew just the belt I was looking for and placed my order. The belt arrived a few days later. While I was waiting for the belt to come in, I removed the front of the dryer and get ready for reinstall. It took me about 15 minutes to install the belt and put the front of the dryer back together. I found PartSelect to be very helpful and saved me, maybe $150.00 by not having to call a serviceman to do the easy replacement. Thank you Steve and PartSelect, now I'm number 1 with the wife again.

well, the hardest part is getting this thing apart - you have to take out the lint trap and remove the two screws from the top. Then I was trying to lift the top off - it's held in place by clips so you have to gently but firmly lift it off from the front end and let it open while still semi attached at the back (like a chest). Detach the electrical wires - they are just clipped in place. Then remove the screws (one on each side) that attach the front panel, and (and this is the hardest part if you don't know how it's attached). You have to SLIGHTLY LIFT the front straight up and then pull it away towards you. I just pulled it off, breaking the little attachers, which I subsequently had to weld back on with a welding compound and leave it overnight to set. the next day was pretty easy though...

The spinning drum is pretty easy to get out and you set it aside. Then I saw the belt pulley sitting there on the bottom of the dryer out of place -- fortunately with the belt there came instructions on how to instal it - READ THOSE INSTRUCTIONS - after that it's cake - put the belt around the center of the drum and feed it through the other parts underneath (this is easier if you tilt the dryer back a bit to get at it better. And you must pull back on that pulley after you have put it in place again - clips into the bottom of the dryer - it's supposed to have a lot of tension on it. Put it all back together and voila!

good luck!

Un pluged and Moved it out from the Wall, Raised the top, found broken belt. ordered belt on line, 2 days belt came in. cleaned all dust and dirt out put greese on berrings for rollers bleu out vent hose with Leef Blower. put top down, pushed back. pluged in and turned on IT WORKS!!!