81572 LG Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Omar from SILVER CITY, NM
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
CHANGED OUT MOTOR
FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOTOR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from CUDAHY, WI
- Parts Used:
- 6323EL2001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
no heat
To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any suggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Randallstown, MD
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
drum motor was not starting when warm, centrifugal switch had broken
removed the top of the dryer first by removing screws in the back and pulling the top back and up. Removed the control panel, followed by the door. The front panel and top brace were then removed. The belt was disengaged by pulling the tensioner idler and working the belt off the motor pulley. The drum was lifted out and set aside with the other parts. Holding the motor shaft with vice-grip pliers, and turning the nut on the blower wheel (left-hand thread!)removed the blower wheel. The motor is held by snap-on retainers and easily removed and swapped. Installation is reverse of disassembly. While in there, cleaned out the lint gathered everywhere. Also constructed a heat shield out of aluminum flashing and foil tape to cover the foil and foam tape between the burner assembly and sheet metal side. The foam had actually burned at some point in the past and the flashing should act as a better heat shield. A relatively easy repair, but should not have been necessary in a 7 year old dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Davenport, IA
- Parts Used:
- MCK49049101
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
a piece of plastic broke by the lint trap
with expert precision
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Grosse Pointe Farms, MI
- Parts Used:
- ADQ56656401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One corner of th elint filter kept sticking up and catching clothes on it.
R&R new lint filter.Old filter appears to have been made improperly and the out frame was warped raising the cormer that kept catching the clothes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rand from Panama City, FL
- Parts Used:
- MEA49050001, ADQ56656401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Lint and guide filter had become damaged
Really easy to do! Unscrewed 4 screws, pulled flap on bottom of inside guide out. Then gently shake assembly to loosen from dryer and pull up and out! Then based on the assembly can replace front or back or both. They snap together! Put assembly replacement back in and close flap and secure in place with the four screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Marriottsville, MD
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Changed mottor
I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '
Was this instruction helpful to you?
Thank you for voting!