Models > 81472 > Instructions

81472 LG Dryer - Instructions

Jump to:

All Instructions for the 81472
61 - 75 of 79
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Ernest from Arcanum, OH
Parts Used:
4581EL2002L
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set
Heard a thumping sound when running
Unplugged the dryer from the wall. Removed the back bracket holding the top on. Then the top will slide back and lift off. Next I removed the screws holding the control panel. Removed the door. Removed all the screws holding the front cover on. Removed the lent shoot. Manually rotated the tumbler. Checked both rollers in the front. Found one with the flat spot in it. Removed and replaced it.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carol from Noblesville, IN
Parts Used:
AJQ75298102
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Drum in Dryer had cracked at front causing a thump as it rotated
First the delivery time was incredible, I ordered the part at 2pm on Mnday and recieved the drum Tuesday afternoon. I'm not sure how this was accomplished as I can't even mail a letter across town and receive the next day. Reoved front of dryer removed old drum and slid in new drum. only difficulty was the wiring disconnect on the control board, didn't want to come off. took 5 minutes to work loose.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Los Altos, CA
Parts Used:
AJQ75298102
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
fractured, broken drum.
Easy repair, more time spent de-linting the inside of the machine and the duct system.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rand from Panama City, FL
Parts Used:
MEA49050001, ADQ56656401
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Lint and guide filter had become damaged
Really easy to do! Unscrewed 4 screws, pulled flap on bottom of inside guide out. Then gently shake assembly to loosen from dryer and pull up and out! Then based on the assembly can replace front or back or both. They snap together! Put assembly replacement back in and close flap and secure in place with the four screws.
Was this instruction helpful to you?
Thank you for voting!
Customer:
BILLHOPEN from SUTTON, WV
Parts Used:
AGM30045804, AGM30045804, 6931EL3002M, 6500EL3001A, AGM30045804
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
My dryer was not heating
First I just replaced the ignitor on a hunch, (disassembly was easy once I saw the video) I also examined the high limit thermostadt and found it was tripped, so I reset the button. the dryer fired up, but soon the thermo tripped again. I found that I could reach it with my arm placed in the inspection port,( about a 4 inch diameter pop out) make sure you unplug first, find the button near the ignitor, and pop it in. the high limit thermo was only holding a few seconds, so I decided to replace it, and did a "shot-gun" approach, replacing all thermos and thermisters at once, only about 35 bucks delivered...BTW, PartSelect shipped them to me at the speed of light.....one day ! Ireplaced all thermos and did and extra scrulpoulous cleaning of the vent. NOTE: it is completely possible that ahe only problem was a reduced vent capacity cmbined with summer heat leading to tripping the high limit thermo....however the thermo was tripping waaaay too easil in my opinion. Anyway, I celebrated doing 10 loads of piled up laundry, and basking in the glory of my wife's admiration for saving a $1000. appliance replacement. "how did you know how to do this honey?" "yoir so smart" (i did'nt tell her about the PartSelect video)
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jason from Davenport, IA
Parts Used:
MCK49049101
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
a piece of plastic broke by the lint trap
with expert precision
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Grosse Pointe Farms, MI
Parts Used:
ADQ56656401
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
One corner of th elint filter kept sticking up and catching clothes on it.
R&R new lint filter.Old filter appears to have been made improperly and the out frame was warped raising the cormer that kept catching the clothes.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 81472
61 - 75 of 79