As clothes move around in the dryer, the agitation and high heat causes items in your dryer to shed some of its fibers. The lint filter collects these fibers to ensure the dryer vent hose does not get...
If your dryer is not turning on, or not heating up, there could be an issue with your thermal fuse. This OEM fuse is designed to act as a high-limit thermostat, and will turn off the heating element i...
This genuine OEM sensor is also known as a moisture sensor or a humidity sensor. It is found underneath the lint filter in your dryer, and is used to detect the amount of moisture present in the drum....
If the drum in your dryer will not tumble, or it is noisy while operating, there may be an issue with the drum belt. The belt is found looped around the dryer drum, a tension pulley, and a motor pulle...
This is an authentic OEM housing for the lint filter in your dryer. This plastic cover helps to protect the actual lint filter, as that part is more delicate. It is important to have a functioning lin...
This is a genuine OEM thermistor with a wire harness included. The thermistor is a temperature sensor that helps to monitor and regulate the temperature inside your dryer. Some signs that you may need...
This is a replacement lint screen guide for your dryer. The lint screen guide attaches to the front bulkhead and supports the lint screen. If your lint screen will not stay in place, or if you are not...
This part is the replacement lint filter cover for your dryer. It is made of gray plastic and is approximately 11-1/2 inches by 1-1/4 inches. The lint filter cover fits on top of the lint filter and p...
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rich
January 2, 2023
The door latch on my washer is broken. I can’t find the part number in the washer manual, is the part the same as the door latch for my LG dryer?
For model number DLEX3370V
Hello Rich, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is Fix Number: FIX3522843 for the Female part of the Latch and Fix Number: FIX3522825 for the Male strike for the latch. We hope this helps, good luck with this repair!
Had to replace front drum support rollers. Removed screws underneath top in back that held bracket that keeps top in place. Slid top towards rear and lifted up. Removed 4 screws that hold plastic front panel in place (inside..2 on each corner) Unplugged front panel electric plugs to remove panel. Opened door..removed 2 screws at bottom of door opening. Removed screws on top of front panel. Unplugged door switch plug. Removed front panel. Removed right front roller with 9/16th wrench for nut. Adjustable for back of stud. Lifted up on drum to get roller out. Reversed to install. Left roller a bit harder to get to stud. Removed and installed same as right side. Did not attempt to replace rear rollers. Have them if needed but very much more involved to replace.
I actually went to mr fix it on u tube. Great instruction on how to take dryer apart. First I unplugged the dryer. I found I could reach the heating system by removing the lint tube in the back of the dryer. I put my I phone with the light on inside the back of the dryer and tested the connections to see if all were working. The thermal fuse was not working. I removed the two wires , red on top and white on the bottom. Then used a small Phillips screwdriver to remove the two mounting screws and removed the fuse. I then used a vacuum to clear any lint from the back of the dryer and inside the dryer. This took me about an hour and a half. I did it this way because I did not want to disassemble the entire dryer to get to the components. I received the fuse in 3 days and tested it. It was fine. I then put it in the dryer screwed it in place, connected the wires. Replaced the lint tube. This took about 10 minutes. Dryer is running great.
Removed existing parts using screwdriver, positioned new parts in dryer and re-inserted screws, tightened - done. Piece of cake, even for someone who cannot saw a straight line with a chop saw.
