DLG3744D LG Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- EDWARD from KNG OF PRUSSA, PA
- Parts Used:
- 5318EL3001A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Igniter burned out
Completely had to dismantle the dryer to get to the igniter.
The screw holding the igniter is a SOB to get at for extraction, and even worse putting back.,
The screw holding the igniter is a SOB to get at for extraction, and even worse putting back.,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from SEQUIM, WA
- Parts Used:
- 3550EL2001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lamp cover broke
Unscrew the screw, remove old part, place in new part, replace screw and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederic from KILLEEN, TX
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old filter seal torn
Pull filter out and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NANCY from ATASCADERO, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dryer was making a terrible sound.
An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from RIVERSIDE, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Loud rumbling noise
Followed video provided on site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Omar from SILVER CITY, NM
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
CHANGED OUT MOTOR
FIRST REMOVED THE LID ON TOP OF DRYER.THEN THE CONTROL PANEL AND THE STEAM TRAY. HAVE TO UNCLIP TWO HARNEST CONNECTORS. REMOVED THE FACE PLATE THAT HOLDS THE DRYER WALLS TOGETHER ALSO REMOVE TO SENSOR HARNESS CLIPS. .REMOVED THE BELT FROM MOTOR. TOOK DRUM OUT . UNCLIPPED MOTOR COLLAR SNAP CLIPS DISCONNECT THE MOTOR HARNESS. INSTALL NE MOTOR AND CONNECT HARNESS INSTALL CLIP . REINSTALL DRUM AND PUT BELT ON. CONNECT HANESSES AND INSTALL FACE PLATE. INSTALL CONTROL PANEL AND THE TOP LID.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D Michael from Plymouth, IN
- Parts Used:
- 4581EL2002L, 4400EL2001A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
noise when you ran dryer
Opened front of dryer - removed drum - replace all 4 rollers (2 had bad shafts) - replace drum with new belt - reassembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from NEWARK, TX
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn dryer lint catcher
Slide out the old lint catcher, and slid in the new one, not that hard.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BOZEMAN, MT
- Parts Used:
- 4027EL1001A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer door would not stay closed
Removed the two screws holding the dryer door strike/locker assembly in place, removed the old and put the new in its place and replaced the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from GOLDFIELD, NV
- Parts Used:
- 6500EL3001A, 5318EL3001A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Persistent smell of propane despite multiple duct cleanings.
Despite the young age of this dryer, and failure of all the other trials to fix the problem, I figured maybe the igniter is the problem. Ordered one. Followed a U tube video to take the unit apart. Noticed immediately that there was lots of lint pretty much everywhere inside the cabinet. Come to find that the blower and the vent had never been connected, with about two inches gap. So, some of the exhaust was going out the vent hose, but lots was not. In fact, lint had coated the propane jet and the air mixer assembly. Replacing the igniter was not particularly difficult, once the dryer was in lots of pieces. I did not test the igniter before replacing it. I did connect the vent outlet to the blower and secured it. End result was a perfectly functioning unit and a happy wife. I don't recall reading about this as a possible cause of propane odor and failure of the unit to heat up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joani from BONNER SPGS, KS
- Parts Used:
- 4948EL4001B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
LP to Natural Gas
The installation of the gas orifice was actually simple. Unscrew the old orifice and screw in the correct orifice. Tricky part of the process was accessing the area of the gas valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from AUSTIN, TX
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My lint filter had a tear.
After trying duct tape to fix the tear, I decided to see if I could just order a new one. Part Select was the first company I found listed, so I ordered one. It was not expensive and it was delivered very quickly! It works so well s as me I’m a very happy customer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from INDIANAPOLIS, IN
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No repairs made, just a new lent filter for the Dryer
Slide out old filter then slide in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from MARANA, AZ
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced lint filter
Removed old lint filter inserted a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eliza from HAUSER, ID
- Parts Used:
- 3550EL1006B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Lint filter
Screw driver, headlight lamp.. a lot of cursing lol it wasn’t too bad I just couldn’t get it in at first
Was this instruction helpful to you?
Thank you for voting!