DLG1320W (ABWEEUS) LG Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mike from LINO LAKES, MN
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace dryer filter
Pull out the worn out dryer filter and replaced it with a new filter that I purchased through Partselect.com.
It fit perfectly.
It fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from N SALT LAKE, UT
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old lint filter was worn out.
I took the old lint filter out and put it in the garbage. I the put the new lint filter in the dryer. Problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from CUDAHY, WI
- Parts Used:
- 5318EL3001A
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
no heat
I replaced the thermistor, then the gas ignitor which were easy to get to once the drum was out. The gas is still not igniting so not sure where to go from here. Putting the drum belt back on took some muscle. But then I'm 71.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sal from MORENO VALLEY, CA
- Parts Used:
- 6323EL2001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Not heat
Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marty from NEOSHO, MO
- Parts Used:
- 6500EL3001A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
HST code given by dryer
Called LG on the phone and they gave the button presses for diagnostics, which then gave the HST code, saying the Humidity sensor was bad.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from OVERLAND PARK, KS
- Parts Used:
- 4027EL1001A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door latch broken
Part showed up in 2 days and repair took 2 min. Very easy. Thank you!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from SEQUIM, WA
- Parts Used:
- 3550EL2001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lamp cover broke
Unscrew the screw, remove old part, place in new part, replace screw and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- temeaco from TULSA, OK
- Parts Used:
- 4027EL1001A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Locker assembly broke
Just unscrewed the original lock and screwed the new one on it was very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MASHPEE, MA
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
I would turn on the dryer it would run for about 10-20 seconds and then shutoff, and could smell something burning
There’s all sorts of videos on it I watched. It was actually very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWARD from KNG OF PRUSSA, PA
- Parts Used:
- 5318EL3001A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Igniter burned out
Completely had to dismantle the dryer to get to the igniter.
The screw holding the igniter is a SOB to get at for extraction, and even worse putting back.,
The screw holding the igniter is a SOB to get at for extraction, and even worse putting back.,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NANCY from ATASCADERO, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dryer was making a terrible sound.
An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederic from KILLEEN, TX
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old filter seal torn
Pull filter out and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from INDIANAPOLIS, IN
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No repairs made, just a new lent filter for the Dryer
Slide out old filter then slide in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from AUSTIN, TX
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My lint filter had a tear.
After trying duct tape to fix the tear, I decided to see if I could just order a new one. Part Select was the first company I found listed, so I ordered one. It was not expensive and it was delivered very quickly! It works so well s as me I’m a very happy customer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joani from BONNER SPGS, KS
- Parts Used:
- 4948EL4001B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
LP to Natural Gas
The installation of the gas orifice was actually simple. Unscrew the old orifice and screw in the correct orifice. Tricky part of the process was accessing the area of the gas valve.
Was this instruction helpful to you?
Thank you for voting!