DLE2301R (ACREEUS) LG Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bryan from Spokane, WA
- Parts Used:
- 5301EL1001J
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dryer wouldn't heat
Removed the heating element, tested it, purchased a new element and installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from Southbury, CT
- Parts Used:
- 4581EL2002L, 4400EL2001A
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Loud rhythmic knocking sound
You will need a helper. Dismantle the Dryer: Remove the screws that hold the top cover, front control panel, front door and front panel. Release the V-Belt under the drum. Remove the Drum. Removed and replace the 2 Front roller assemblies - these were completely worn. Replaced the 2 rear rollers (did not replace the rear roller axels as these were more difficult to remove and they were in good shape) and the V-Belt while I had the whole thing open. Use a shop vac and cleaned up the whole unit. It is so nice and quiet now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Boise, ID
- Parts Used:
- AJQ75298102
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Hole in drum
Found YouTube video followed it closely and did extensive cleaning. The lint on the felt of the drum was causing a rough rotation as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Los Altos, CA
- Parts Used:
- AJQ75298102
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
fractured, broken drum.
Easy repair, more time spent de-linting the inside of the machine and the duct system.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Goodyear, AZ
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint screen had a damaged felt gasket.
Could not fix original part. Ordered new lint screen and place it the dryer. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Saint Augustine, FL
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new lint filter
Quick online ordering, part delivered to my home in 2 days! Yay! No more gross lint filter. The new one is exactly what is needed. Thanks! I would definitely order again with your company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Parker, CO
- Parts Used:
- 4027EL1001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door wouldn't stay latched
Unscrewed the dryer latch on the dryer (not the piece on the dryer door) and screwed in the new piece! Bam, done and done. The ordering process was a snap, very friendly on the phone. She even emailed me a picture of the part before I ordered to make sure it was the right one, and was so patient with me, while my kids were sort of loud in the background. Thanks PartSelect.com, your part is quality and employee rocks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Fremont, OH
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Loud squealing noise coming from dryer.
Not knowing whether it was the pulley, tensioner, or drum roller I had previously pulled the dryer apart and noticed one roller shaft was rusty for some reason. When the part came in (which was quite fast)I disassembled the dryer to the point that I could remove the left rear drum roller. Replaced the roller and reassembled the dryer (to my surprise without any extra screws or parts left). Fairly easy job, just time consuming.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Iowa, LA
- Parts Used:
- 4400EL2001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
belt slipping, drum will not turn
I first took the top off, then the front control panel, unplugged the wires from panel (very easy), took the front panel off, the rum comes out very easy, be sure to look at the way the belt goes back on the pulley. I didn't and it took me a while to figure it out. All goes back together very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Randallstown, MD
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
drum motor was not starting when warm, centrifugal switch had broken
removed the top of the dryer first by removing screws in the back and pulling the top back and up. Removed the control panel, followed by the door. The front panel and top brace were then removed. The belt was disengaged by pulling the tensioner idler and working the belt off the motor pulley. The drum was lifted out and set aside with the other parts. Holding the motor shaft with vice-grip pliers, and turning the nut on the blower wheel (left-hand thread!)removed the blower wheel. The motor is held by snap-on retainers and easily removed and swapped. Installation is reverse of disassembly. While in there, cleaned out the lint gathered everywhere. Also constructed a heat shield out of aluminum flashing and foil tape to cover the foil and foam tape between the burner assembly and sheet metal side. The foam had actually burned at some point in the past and the flashing should act as a better heat shield. A relatively easy repair, but should not have been necessary in a 7 year old dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Arcanum, OH
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Heard a thumping sound when running
Unplugged the dryer from the wall. Removed the back bracket holding the top on. Then the top will slide back and lift off. Next I removed the screws holding the control panel. Removed the door. Removed all the screws holding the front cover on. Removed the lent shoot. Manually rotated the tumbler. Checked both rollers in the front. Found one with the flat spot in it. Removed and replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Noblesville, IN
- Parts Used:
- AJQ75298102
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum in Dryer had cracked at front causing a thump as it rotated
First the delivery time was incredible, I ordered the part at 2pm on Mnday and recieved the drum Tuesday afternoon. I'm not sure how this was accomplished as I can't even mail a letter across town and receive the next day. Reoved front of dryer removed old drum and slid in new drum. only difficulty was the wiring disconnect on the control board, didn't want to come off. took 5 minutes to work loose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from Burkesville, KY
- Parts Used:
- 4027EL1001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The latch on the dryer door was broken. I ordered the part, had it the next day and took it home to fix my dryer.
It only took about 5 minutes to fix the problem. Took out two screws, removed old part, put the new one on and replaced the screws. Works great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberta from Los Angeles, CA
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
frame of lint filter got bent out of shape
Simply removed the old filter and put in the new one. I was impressed with the sales person when I ordered the filter by phone. The online site didn't have a photo of it - just a description and price. She reassured me that I was ordering the correct item--she was very friendly. And the price was reasonable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from Longview, TX
- Parts Used:
- 4581EL2002L, AJQ75298102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer making bumping noise
Followed instruction obtained from parts select. removed top. removed wires removed control panel removed front of dryer pulled out drum assemble changed rollers installed new drum reinstalled front of dryer installed controll panel hooked up wires installed top
Was this instruction helpful to you?
Thank you for voting!