RV1044AS (ABWESEU) LG Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from JOHNSON CITY, TN
- Parts Used:
- 4400EL2001F
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Shrieking noise when the dryer tried to turn
I assumed this was a belt problem. Ordered the belt and followed the excellent screw by screw instructional YouTube provided by PartSelect. In fact, I probably would not have attempted the repair, until I watched the video and was reassured that I could do it. When I got the front panel off, the problem was obvious. There was a dishrag stuck in the blower. Didn't need the belt, but the video was sure worth the price of the part (~$17). Mr. Appliance charges $109 to DIAGNOSE the problem! This was way easier than dealing with them, especially during a pandemic near the holidays.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from LINO LAKES, MN
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace dryer filter
Pull out the worn out dryer filter and replaced it with a new filter that I purchased through Partselect.com.
It fit perfectly.
It fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from N SALT LAKE, UT
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old lint filter was worn out.
I took the old lint filter out and put it in the garbage. I the put the new lint filter in the dryer. Problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joaquin from MIAMI BEACH, FL
- Parts Used:
- EBF61496102
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer work but wouldn’t shut off when finished cycle, had to shutoff from breaker
With a thin flat screwdriver I was able to pry out the old door switch, I replaced it with the new door switch, pushed back in dryer and so far is working since I installed a month ago.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Mendham, NJ
- Parts Used:
- 6931EL3003D
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Heater wouldn't get hot - suspected thermal fuse
Removed the top, the control panel and the door. The heater assembly came out thru the front, without having to remove the drum. Easy replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sergio from CORNELIUS, OR
- Parts Used:
- 3045EL1002K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broke the tub drum
Exchange
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from RENO, NV
- Parts Used:
- 3045EL1002K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum cracked
Repair was easy, but the part does not come with directions. It is pretty self explanatory if you are used to taking things apart and fixing them. Otherwise there are YouTube videos you can pull up. Dryer runs like it is new again though and it was way cheaper than buying a new dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sal from MORENO VALLEY, CA
- Parts Used:
- AGM30045804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Not heat
Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marty from NEOSHO, MO
- Parts Used:
- 6500EL3001A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
HST code given by dryer
Called LG on the phone and they gave the button presses for diagnostics, which then gave the HST code, saying the Humidity sensor was bad.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MASHPEE, MA
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
I would turn on the dryer it would run for about 10-20 seconds and then shutoff, and could smell something burning
There’s all sorts of videos on it I watched. It was actually very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederic from KILLEEN, TX
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old filter seal torn
Pull filter out and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from AUSTIN, TX
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My lint filter had a tear.
After trying duct tape to fix the tear, I decided to see if I could just order a new one. Part Select was the first company I found listed, so I ordered one. It was not expensive and it was delivered very quickly! It works so well s as me I’m a very happy customer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from NEWARK, TX
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn dryer lint catcher
Slide out the old lint catcher, and slid in the new one, not that hard.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from INDIANAPOLIS, IN
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No repairs made, just a new lent filter for the Dryer
Slide out old filter then slide in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Michigamme, MI
- Parts Used:
- 6931EL3003D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
thermal fuse went out
Watched a repair video. Very easy to replace, about an hour to repair.
Was this instruction helpful to you?
Thank you for voting!