RN1393AS (ABWEEUS) LG Dryer - Instructions

I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.

I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.

I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '

You will need a helper. Dismantle the Dryer: Remove the screws that hold the top cover, front control panel, front door and front panel. Release the V-Belt under the drum. Remove the Drum. Removed and replace the 2 Front roller assemblies - these were completely worn. Replaced the 2 rear rollers (did not replace the rear roller axels as these were more difficult to remove and they were in good shape) and the V-Belt while I had the whole thing open. Use a shop vac and cleaned up the whole unit. It is so nice and quiet now.

Found YouTube video followed it closely and did extensive cleaning. The lint on the felt of the drum was causing a rough rotation as well.

Easy repair, more time spent de-linting the inside of the machine and the duct system.

with expert precision

This was a repair from a repair. It started as a conversion to LPG, in the process the igniter broke. The parts arrived quickly and we were able to get it back together and the wife is happy. Thanks.

Not knowing whether it was the pulley, tensioner, or drum roller I had previously pulled the dryer apart and noticed one roller shaft was rusty for some reason. When the part came in (which was quite fast)I disassembled the dryer to the point that I could remove the left rear drum roller. Replaced the roller and reassembled the dryer (to my surprise without any extra screws or parts left). Fairly easy job, just time consuming.

I first took the top off, then the front control panel, unplugged the wires from panel (very easy), took the front panel off, the rum comes out very easy, be sure to look at the way the belt goes back on the pulley. I didn't and it took me a while to figure it out. All goes back together very easy.

removed the top of the dryer first by removing screws in the back and pulling the top back and up. Removed the control panel, followed by the door. The front panel and top brace were then removed. The belt was disengaged by pulling the tensioner idler and working the belt off the motor pulley. The drum was lifted out and set aside with the other parts. Holding the motor shaft with vice-grip pliers, and turning the nut on the blower wheel (left-hand thread!)removed the blower wheel. The motor is held by snap-on retainers and easily removed and swapped. Installation is reverse of disassembly. While in there, cleaned out the lint gathered everywhere. Also constructed a heat shield out of aluminum flashing and foil tape to cover the foil and foam tape between the burner assembly and sheet metal side. The foam had actually burned at some point in the past and the flashing should act as a better heat shield. A relatively easy repair, but should not have been necessary in a 7 year old dryer.

Unplugged the dryer from the wall. Removed the back bracket holding the top on. Then the top will slide back and lift off. Next I removed the screws holding the control panel. Removed the door. Removed all the screws holding the front cover on. Removed the lent shoot. Manually rotated the tumbler. Checked both rollers in the front. Found one with the flat spot in it. Removed and replaced it.

First the delivery time was incredible, I ordered the part at 2pm on Mnday and recieved the drum Tuesday afternoon. I'm not sure how this was accomplished as I can't even mail a letter across town and receive the next day. Reoved front of dryer removed old drum and slid in new drum. only difficulty was the wiring disconnect on the control board, didn't want to come off. took 5 minutes to work loose.

well after hurricane sandy we had a family of 5 stay with us. after the storm we retrieved most of thier clothing and started washing. the machine worked off of a generator for 4 days almost around the clock. overloaded at times i might add. these folks lost just about everything. my wife noticed a noise i opened the machine and saw the cracked drum. i ordered a new one from you guys and saved the $900 on a new machine. together we breathed new life into it. thanks!!!

Followed instruction obtained from parts select. removed top. removed wires removed control panel removed front of dryer pulled out drum assemble changed rollers installed new drum reinstalled front of dryer installed controll panel hooked up wires installed top