DLE3400W (ABWEUUS) LG Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Houston, TX
- Parts Used:
- 6931EL3002M, AGM30045804
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer wasn't getting hot enough
Removed the exhaust duct screw and removed the duct. Hardest part of the repair was reaching in one-handed to remove the screws for the parts. Make sure that the screwdriver is magnetic. Changed parts and dryer working better than it has in months.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from Burkesville, KY
- Parts Used:
- 4027EL1001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The latch on the dryer door was broken. I ordered the part, had it the next day and took it home to fix my dryer.
It only took about 5 minutes to fix the problem. Took out two screws, removed old part, put the new one on and replaced the screws. Works great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Parker, CO
- Parts Used:
- 4027EL1001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door wouldn't stay latched
Unscrewed the dryer latch on the dryer (not the piece on the dryer door) and screwed in the new piece! Bam, done and done. The ordering process was a snap, very friendly on the phone. She even emailed me a picture of the part before I ordered to make sure it was the right one, and was so patient with me, while my kids were sort of loud in the background. Thanks PartSelect.com, your part is quality and employee rocks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILLHOPEN from SUTTON, WV
- Parts Used:
- AGM30045804, AGM30045804, 6931EL3002M, 6500EL3001A, AGM30045804
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
My dryer was not heating
First I just replaced the ignitor on a hunch, (disassembly was easy once I saw the video) I also examined the high limit thermostadt and found it was tripped, so I reset the button. the dryer fired up, but soon the thermo tripped again. I found that I could reach it with my arm placed in the inspection port,( about a 4 inch diameter pop out) make sure you unplug first, find the button near the ignitor, and pop it in. the high limit thermo was only holding a few seconds, so I decided to replace it, and did a "shot-gun" approach, replacing all thermos and thermisters at once, only about 35 bucks delivered...BTW, PartSelect shipped them to me at the speed of light.....one day ! Ireplaced all thermos and did and extra scrulpoulous cleaning of the vent. NOTE: it is completely possible that ahe only problem was a reduced vent capacity cmbined with summer heat leading to tripping the high limit thermo....however the thermo was tripping waaaay too easil in my opinion. Anyway, I celebrated doing 10 loads of piled up laundry, and basking in the glory of my wife's admiration for saving a $1000. appliance replacement. "how did you know how to do this honey?" "yoir so smart" (i did'nt tell her about the PartSelect video)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennisd from Waco, TX
- Parts Used:
- AGM30061302, AGM30045804, AGM30045804
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Shutting off a while after starting. Burning smell.
Seemed to be shutting off on the safety thermostat so I replaced them all. Works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Spokane, WA
- Parts Used:
- 5301EL1001J
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dryer wouldn't heat
Removed the heating element, tested it, purchased a new element and installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Inland Commercial Appliance from Moreno Valley, CA
- Parts Used:
- AGM30045804, AGM30045804, 6931EL3002M, 6500EL3001A, AGM30045804
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Not heating correctly
Removed Top, then front and drum. Parts easy to access once drum is out. Recommend reading up on drum replacement. Would appear that all repairs will require taking it out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Iowa, LA
- Parts Used:
- 4400EL2001F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
belt slipping, drum will not turn
I first took the top off, then the front control panel, unplugged the wires from panel (very easy), took the front panel off, the rum comes out very easy, be sure to look at the way the belt goes back on the pulley. I didn't and it took me a while to figure it out. All goes back together very easy.
Was this instruction helpful to you?
Thank you for voting!