RV1310A (ABWEEUS) LG Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sarah from Burkesville, KY
- Parts Used:
- 4027EL1001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The latch on the dryer door was broken. I ordered the part, had it the next day and took it home to fix my dryer.
It only took about 5 minutes to fix the problem. Took out two screws, removed old part, put the new one on and replaced the screws. Works great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Grosse Pointe Farms, MI
- Parts Used:
- ADQ56656401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One corner of th elint filter kept sticking up and catching clothes on it.
R&R new lint filter.Old filter appears to have been made improperly and the out frame was warped raising the cormer that kept catching the clothes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Parker, CO
- Parts Used:
- 4027EL1001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door wouldn't stay latched
Unscrewed the dryer latch on the dryer (not the piece on the dryer door) and screwed in the new piece! Bam, done and done. The ordering process was a snap, very friendly on the phone. She even emailed me a picture of the part before I ordered to make sure it was the right one, and was so patient with me, while my kids were sort of loud in the background. Thanks PartSelect.com, your part is quality and employee rocks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Arcanum, OH
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Heard a thumping sound when running
Unplugged the dryer from the wall. Removed the back bracket holding the top on. Then the top will slide back and lift off. Next I removed the screws holding the control panel. Removed the door. Removed all the screws holding the front cover on. Removed the lent shoot. Manually rotated the tumbler. Checked both rollers in the front. Found one with the flat spot in it. Removed and replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rand from Panama City, FL
- Parts Used:
- MEA49050001, ADQ56656401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Lint and guide filter had become damaged
Really easy to do! Unscrewed 4 screws, pulled flap on bottom of inside guide out. Then gently shake assembly to loosen from dryer and pull up and out! Then based on the assembly can replace front or back or both. They snap together! Put assembly replacement back in and close flap and secure in place with the four screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Fremont, OH
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Loud squealing noise coming from dryer.
Not knowing whether it was the pulley, tensioner, or drum roller I had previously pulled the dryer apart and noticed one roller shaft was rusty for some reason. When the part came in (which was quite fast)I disassembled the dryer to the point that I could remove the left rear drum roller. Replaced the roller and reassembled the dryer (to my surprise without any extra screws or parts left). Fairly easy job, just time consuming.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Spokane, WA
- Parts Used:
- 5301EL1001J
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dryer wouldn't heat
Removed the heating element, tested it, purchased a new element and installed.
Was this instruction helpful to you?
Thank you for voting!