79661422410 LG Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gabriella from Lexington, VA
- Parts Used:
- 5231EL1001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer lint filter lining was falling apart and lint was not being filtered
Ordered a new Dryer Lint Filter Assembly that fit my LG electric dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from TROY, TX
- Parts Used:
- 6913EL3001E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light bulb in dryer burndt
Removed cover replaced bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Florence, MA
- Parts Used:
- 6500EL3001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dryer turned off quickly with clothes still wet
Unscrewed the sensor cover, which on this model also holds the lint filter in plas. Then pulled the old sensors from their plug-ins. The new sensors easily slipped into the holder, and then replugged to the wires. The whole assembly screwed back into place. One note of caution: the flap where the filter slides in goes inside the cover, it's default is not upright, and be careful to not allow the inside spring for the cover to come off, or you might chase it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Michigamme, MI
- Parts Used:
- 6931EL3003D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
thermal fuse went out
Watched a repair video. Very easy to replace, about an hour to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Tavares, FL
- Parts Used:
- 6500EL3001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Had an issue with the dryer not drying the clothes in the allotted time and turning the dryer off. I knew it was still getting heat so I googled the issue with suggestions.
I watched a YouTube video with how to take the dryer apart and remove the sensors. I followed the what the instructions were removing the top of the dryer and then the front panel. Once that was removed it was a matter of removing 7 more screws and the lint collector piece came off. Popped the sensor pieces out. Cleaned the inside of the dryer and reinstalled a total of 5 parts and dryer is working fine and the clothes are drying in the allotted time it use to take.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Dagsboro, DE
- Parts Used:
- 3550EL2004B
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cover fell of due to broken center hinge.
Removed six screws holding filter support in place. Replaced cover (keep track of the small spring on the left stub shaft). Reinstall cover and filter support sections. NOTE: the cover does not come with a new spring. You have e to reuse the old spring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from RIVERSIDE, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Loud rumbling noise
Followed video provided on site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from DAWSONVILLE, GA
- Parts Used:
- 3911EZ9131X
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Install aftermarket side vent kit
I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from CUDAHY, WI
- Parts Used:
- AGM30045804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
no heat
To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any suggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D Michael from Plymouth, IN
- Parts Used:
- 4581EL2002L, 4400EL2001F
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
noise when you ran dryer
Opened front of dryer - removed drum - replace all 4 rollers (2 had bad shafts) - replace drum with new belt - reassembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Whittier, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Thumping sound when dryer is on.
I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennisd from Waco, TX
- Parts Used:
- AGM30061302, AGM30045804, AGM30045804
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Shutting off a while after starting. Burning smell.
Seemed to be shutting off on the safety thermostat so I replaced them all. Works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Inland Commercial Appliance from Moreno Valley, CA
- Parts Used:
- AGM30045804, AGM30045804, 6931EL3002M, 6500EL3001A, AGM30045804
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Not heating correctly
Removed Top, then front and drum. Parts easy to access once drum is out. Recommend reading up on drum replacement. Would appear that all repairs will require taking it out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from Southbury, CT
- Parts Used:
- 4581EL2002L, 4400EL2001F
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Loud rhythmic knocking sound
You will need a helper. Dismantle the Dryer: Remove the screws that hold the top cover, front control panel, front door and front panel. Release the V-Belt under the drum. Remove the Drum. Removed and replace the 2 Front roller assemblies - these were completely worn. Replaced the 2 rear rollers (did not replace the rear roller axels as these were more difficult to remove and they were in good shape) and the V-Belt while I had the whole thing open. Use a shop vac and cleaned up the whole unit. It is so nice and quiet now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILLHOPEN from SUTTON, WV
- Parts Used:
- AGM30045804, AGM30045804, 6931EL3002M, 6500EL3001A, AGM30045804
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
My dryer was not heating
First I just replaced the ignitor on a hunch, (disassembly was easy once I saw the video) I also examined the high limit thermostadt and found it was tripped, so I reset the button. the dryer fired up, but soon the thermo tripped again. I found that I could reach it with my arm placed in the inspection port,( about a 4 inch diameter pop out) make sure you unplug first, find the button near the ignitor, and pop it in. the high limit thermo was only holding a few seconds, so I decided to replace it, and did a "shot-gun" approach, replacing all thermos and thermisters at once, only about 35 bucks delivered...BTW, PartSelect shipped them to me at the speed of light.....one day ! Ireplaced all thermos and did and extra scrulpoulous cleaning of the vent. NOTE: it is completely possible that ahe only problem was a reduced vent capacity cmbined with summer heat leading to tripping the high limit thermo....however the thermo was tripping waaaay too easil in my opinion. Anyway, I celebrated doing 10 loads of piled up laundry, and basking in the glory of my wife's admiration for saving a $1000. appliance replacement. "how did you know how to do this honey?" "yoir so smart" (i did'nt tell her about the PartSelect video)
Was this instruction helpful to you?
Thank you for voting!