81379 (ASRESEU) LG Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mike from LINO LAKES, MN
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace dryer filter
Pull out the worn out dryer filter and replaced it with a new filter that I purchased through Partselect.com.
It fit perfectly.
It fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from N SALT LAKE, UT
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old lint filter was worn out.
I took the old lint filter out and put it in the garbage. I the put the new lint filter in the dryer. Problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joaquin from MIAMI BEACH, FL
- Parts Used:
- EBF61496102
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer work but wouldn’t shut off when finished cycle, had to shutoff from breaker
With a thin flat screwdriver I was able to pry out the old door switch, I replaced it with the new door switch, pushed back in dryer and so far is working since I installed a month ago.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from RENO, NV
- Parts Used:
- 3045EL1002K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum cracked
Repair was easy, but the part does not come with directions. It is pretty self explanatory if you are used to taking things apart and fixing them. Otherwise there are YouTube videos you can pull up. Dryer runs like it is new again though and it was way cheaper than buying a new dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marty from NEOSHO, MO
- Parts Used:
- 6500EL3001A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
HST code given by dryer
Called LG on the phone and they gave the button presses for diagnostics, which then gave the HST code, saying the Humidity sensor was bad.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sergio from CORNELIUS, OR
- Parts Used:
- 3045EL1002K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broke the tub drum
Exchange
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sal from MORENO VALLEY, CA
- Parts Used:
- 6323EL2001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Not heat
Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MASHPEE, MA
- Parts Used:
- 4681EL1008A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
I would turn on the dryer it would run for about 10-20 seconds and then shutoff, and could smell something burning
There’s all sorts of videos on it I watched. It was actually very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Aurora, CO
- Parts Used:
- 4581EL2002L, 4400EL2001F
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dryer was extremely noisy
This was all pretty straightforward with the helpful video hosted on this site. The only issues I ran into was I had a seized screw that stripped and I had to drill it out and replace it. Also, I had to disassemble the front and rear a little bit further than what is shown in order to install the new roller axles. I was pleasantly surprised that I did not have to worry about the triangular retainers, because the replacement rollers/axles use an improved metal retaining pin. Overall, I'm very happy and the dryer is nearly silent now. It was a bit of a challenge but I took my time and gave myself breaks throughout the morning rather than banging my head against the wall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from SEQUIM, WA
- Parts Used:
- 3550EL2001A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lamp cover broke
Unscrew the screw, remove old part, place in new part, replace screw and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from TROY, TX
- Parts Used:
- 6913EL3001E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light bulb in dryer burndt
Removed cover replaced bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederic from KILLEEN, TX
- Parts Used:
- 5231EL1003B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old filter seal torn
Pull filter out and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NANCY from ATASCADERO, CA
- Parts Used:
- 4581EL2002L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dryer was making a terrible sound.
An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from MANHASSET, NY
- Parts Used:
- 3550EL2004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken link vet flap
Removed the old vent trap 3 screws total and replaced the new very quick and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Mendham, NJ
- Parts Used:
- 6931EL3003D
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Heater wouldn't get hot - suspected thermal fuse
Removed the top, the control panel and the door. The heater assembly came out thru the front, without having to remove the drum. Easy replacement
Was this instruction helpful to you?
Thank you for voting!