WD1243FHB (OWEECI) LG Dryer - Instructions

Found on line OE meant washer not pumping out water with the suggestion to clean the filter and inspect the pump and lines for blockage. No problems there. You must be careful to empty the water manually before removing the filter. My wet vac helped but I still made a mess. I found a mechanic to look at the washer. He said it is common for the pump on these washers to go bad, especially if the washer has sat out of service. They wanted $300 to replace the pump. I found the part on this website for $53 and replaced it myself. The only hard part was emptying the water without making a mess and leaning the washer up and back far enough safely to remove the pump, then working on my back under the machine.

This was very easy to instal. The aplaiance repair co. wanted $240 my LG is six years old and would rather buy a new one if I had to spend that much, so I gave it a shot and it took me 20 min to install the part. Told my wife she owed me $ 180 for my labor.

I watched a video of how to replace the pump and it showed taking the top and front off to get to it. I actually found this could be done by removing the back panel from the washer. There were two hose clamps you have to squeeze and slide up and two wires going to the pump. There are three screws holding the pump that need to be removed from the front of the washer. Once these are removed all you have to do is push a tab down and the motor slide right out. The pump assembly can also be reached from the bottom of the washer.

Tipped the washer on its side to expose the bottom, removed the plastic lid adjacent to the pump after removing the screws holding it , then, using a flat head on a pry tab pulled out the pump, removed the hoses with pliers to complete the extraction, swapped the pump on my bench. . assembly is reverse of disassembly. .

Followed the instructions that a fellow DIYer posted in PartSelect and a few I watched on Youtube. Pull out the detergent drawer, remove the back screws, slide the top off, unclip the control board, unplug Power & One more switch so that I could move it aside. Take the gasket retention wire off the door gasket & tuck it inside. Remove the screws in the bottom & top. Then slide the front panel, including the door up (not easy) and out. The part received was only the pump motor so I had to take a few pictures before so I knew I got it together right. Remove drain houses, pump screws, slide pump back and remove pump. A few more screws to remove the pump from the housing & replace with new pump. Put it all back together. It works! It only took about 45 minutes

We drained the water from the washer via the tiny hose/filter located at the lower left corner of the washing machine. The unit was then pulled away from the wall, unplugged and the hoses disconnected. At this time, we used the wet dry vacuum to suction the water that remained in the drain hose. We tilted the washing machine back until the front of the unit was 18 inches or so off the floor. We used the foot stool to hold the washer up in the air so that we could work on the pump. Replacing the pump was as easy as removing a few screws, unplugging the electrical connections and removing the faulty pump assembly from the plastic housing. (Be sure to mark what connector goes in what terminal). Re-assemble. Re-connect. You are ready to go. It took more time to ready the washer than it did to replace the part.

ordered part from Part Select and it was here very quickly,but the part came damaged (not the fault of Part Select). I ordered another one and PartSelect had it here the next day. I watched the video on how to replace it and it was very helpfull.The particular part I replaced (pump motor) does not seem very durable. I will buy an American made washer the next time I need one. I will use Partselect in the future and recomend it to others.

The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.

took out the drain pump and replace with a new one

During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it relatively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.

Found great Youtube video, followed step by step. Only difficult part was getting the tub gasket clamp back on. But all in all pretty easy. If tub won't drain and weird noise coming from pump do not hesitate to do it yourself and save some coin!

The pump is apparently used for more than one washer, and the R&R instructions may be significantly different. I found a youtube video for my exact washer.

Removed the top, the front, got to the pump, removed it and replace it with the new one.

Found the part of Part Select by describing the problem. used a Utube video and step by step we were able to take apart, replace and put back everything with just a screw driver - I saved so much money!

greate very easy and the parts fit awsome the shiping was fast and easy very satified